I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Hi
I've recently been working on the ncp host example provided by nordic. after downloading the standalone version from the site, I tried programming the 2 nRF 52840 dk...
nRF SDK 17.1.0 with SD140 7.2.0
There is no example for how to use the sd_rand library. I've seen scant few posts that mention functions like sd_rand_application_bytes_available_get...
Hi I've just started developing with the nrf52840 and Ive been following the official documentation on how to use the programmer shipped with nRF Connect.
Unfortunately...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
Hi there,
The spec for nRF52840 says in sec 6.33.1 that for UART, "The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable communication...
Hi,
How do you export your project from nRF Connect within VSC? You may have modifications you did for DTS files, prj.conf etc, that you may miss if you focus on just src...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
HI,
In our application, there is strange dependency for BLE service. The device is getting detected on ble scan only if we flash the ble application after flashing an application...
Hello,
with iOS 16 the connection during the update of the Firmware with IOS-DFU-Library not working. It is stop after few second with the error 202.
Do you know any solutions...
Hi, I restart advertising with ble_advertising_start and sd_ble_gap_adv_stop because I need to change the advertising interval in different situations. I am observing high...
I use nRF Connect for Desktop v3.12.0 (the latest) and its apps:
Bluetooth Low Energy (the latest standalone application v4.0.0)
Programmer v3.0.4 (the latest)
Can...
Is there support now for coded phy on nrf ble sniffer?
I'm using the nrf52840 devkit (hardware version 2.0.2 which supports coded phy) and sniffer works fine without coded...
It looks like the BT Mech spec has not been updated since 2017. Is there an update in progress and is Instaburst (or similar function) a candidate feature?
This would seem...
