Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem. ...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
I'm trying to generate a service key and token so that I can access AGPS services on nRF Cloud. The documentation says that clicking on 'Device Management' the panel that...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
TWI Master drives BNO085 to read four-element data at intervals of 20ms, and I2C will not be able to read data when the device works for more than 10 minutes. INITTWI and...
I have verified The maximum channel table size NRF_GZLL_CONST_MAX_CHANNEL_TABLE_SIZE is 32.
but result_value = nrf_gzll_set_channel_table(my_channel_table, 32) return false...
Hi, I am trying to reach the highest possible throughput when sending data over usb to nRF52840 from a host computer, but I am reaching 4Mbps max. Is this reasonable or is...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello,
I am working on creating a custom board based off the nrf5340dk_nrf5340 board
I am following the tutorial here
https://academy.nordicsemi.com/courses/nrf-connect...
Hello,
I would like to know if there is official C# source code to perform DFU OTA for a NRF52840 from Windows without Nordic hardware (DK, dongles etc..), using only the...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hi
I am getting an error while building source code. The same code used to build while using NRF connect SDK version 2.5.1. Currently I am using nRF Connect SDK version...
Hi,
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...