Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello,
I'm trying to get the SPI drivers working in slave mode. I have tested my master (Atmel L21) on an Arduino and I can see my message clearly. I'm trying to get nRF52833...
Hello
I want to access to the buffer to see what I am transmitting for then change the data to transmit to be able to verify, also I want to know where I can find de Kconfig...
Hi!
I have a custom board with a NRF52840 and some extra sensors for my application. I'm trying to comunicate with one SPI sensor but I have a little extrange behavior....
Hi,
I am trying to create a combined Bootloader + Bootloader Settings + Application hex file to flash the same into the devices during the production.
Bootloader Project...
i write 40bytes to flash 0x74000 and read 0x74000。i find it actually use 160bytes. I try to write a different number of bytes, it actually use 4*(write bytes)
this is...
I wonder if I can use spi1 or i2c1 on nrf9160. I use the 9160ns board configuration but non of my configs work for spi1 or i2c1 works. If I change it to i2c2 or others it...
I have a startup sequenced (nRF52832 peripheral) based on the s132 (v7.0.1 BLE 5.1) NFC Pairing example where it advertises at 1Msps link rate, then uses the PHY UPDATE API...
Hello!
We are working with NRF52840 dongles and want to be able to have them relay data over an OpenThread mesh network through UDP automatically. We have found within...
Hi,
calling "nrf_ringbuf_get()" immediately after "nrf_ringbuf_cpy_get()" returns an invalid pointer to the data. A workaround could be to assign "rd_idx" to "tmp_rd_idx...
Hi to all,
I have designed a custom board with 3rd party module (RAYTAC MDBT50Q) which includes NRF52840. During debugging on the custom board, two modules were demaged...
Hello,
I am using serial LTE modem for communication.
After trying to connect to TCP server using AT#XCONNECT I get following error:
The only official documentation...
In a system based on one nrf52-ble-app-uart-c-multilink-master and multiple ble_app_uart, the data from any entity is sent to all devices.
i.e. each ble_app_uart is sending...
Hello,
I'm using BLE peripheral device. I need to connect it to a BLE central device and exchange data. There are some connection procedure-
1. Discovered Bluetooth devices...
Hello, everyone, when I call err_code = fds_record_update(&record_desc, &record), I sometimes get an error: FDS_ERR_NO_SPACE_IN_FLASH.
Therefore, when this error occurs...
I have the nRF52 PCA10040 DK device, and I'm downloading the code from the online mbed tutorial. I'm using Putty serial port to communicate with the device at 9600 baud rate...
