Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
We have a door lock product. At first, the capacitance value of bluetooth frequency deviation was not adjusted, and then it was very difficult for apple to connect with vivo...
Hi,
I have a problem that can not receive FDS_EVT_WRITE event, but fds_record_write return NRF_SUCCESS when using FDS and FreeRTOS simultaneously on nRF52840. And FDS_EVT_INIT...
Hi,
In the ble_app_uart example I am trying to read a binary file and send it to the application using nRF52840 board. I have send 32 packets of data periodically.If a delay...
Hi. I am looking for a reference FW design for BTLE where I can define a custom Service and Characteristic where I can send arbitrary (minimal length) data from peripheral...
Hi,
In our application, LCD will occupy 150KB RAM, and algorithm will occupy 60KB, but 52840 only has 256KB ram, so 256KB RAM is not enough for our application;
We want...
To realize multi touch in hid, we need to realize get report request to get the maximum number of support points and set report request to set touch mode. In the SDK 15.3...
Hello,
I'm trying to add a third characteristic to my BLE service and when I add it, my device "fatally" crashes in Release mode with no meaningful error information ...
Hi I'm having trouble updating the firmware on a custom board using JTAG through the NRF9160 DK.
I've attached the log file from the programmer of the error I'm getting...
I loaded up the zephyr sample blinky example, compiled ok, and went to download to the nrf5340-pdk...
I got the following error dialog plus some more misc. errors (see output...
Hi
nrf52833 SDK16
The following code works fine on UART 0 but not on UART 1
The problem seems to come from nrfx_uart.c
There is no support for a UART1, so...
Hi,
I've built a project out of the USBD_ACM_CDC example in which I have added a SPI master driver. This project has a timer interrupt that will shoot off every ~500us and...
Hi everyone,
I'm a beginner with nordic development and I managed to screw up my development kit. It started when I was trying to figure out the BLE blinky app with my IOS...
Hi,
I'm working on an IoT project with NRF52832 ( S132) . I need to connect this device to mqtt over 6LoWPAN (IPv6) and run it on a button cell battery CR2032 for as long...
HI,
I am trying to connect to our cloudmqtt account where the topics are dynamically created because of which is it not possible to pre-program a specific topic.
I would...
Hi,
it came to my attention that the inductor Murata LQP15MN3N9B02D (3.9nH) that is used in the antenna matching circuit of the nrf52832 reference design has become NRND...
