I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi, I'm using nRF Mesh App to provision more than 5 devices for vendor specific models other than on/off model. My purpose is to send some data instead of on/off the light...
Hi all
I am using a nRF52840 with SDK 15.3.0 and s140_nrf52_6.1.1 soft device.
My application is a multi-peripheral device that has a common service, each peripheral can...
Hi
I'm really new to this, forgive me it's a stupid question. I'm using the nRF52 DK from Nordic.
I started with the "Developing with SEGGER Embedded Studio", but when...
In the user manual of nrf52832 it is said that ram[n].power are retained registers in sleep mode and that depending on the settings.
One or more RAM sections can be retained...
Dear Nordic DevZone Team, With ARM cortex M4, it is possible to go into deep sleep mode. In the Nordic nRF52832 which uses M4, it is configured for BLE advertising. I would...
Hi
I read nRF52840 - LPCOMP information on datasheet and SDK.
It shows VHYST value is 35mV (typ.) in datasheet page 191 and 50mV (typ.) in SDK - nrf_lpcomp.h.
which...
Hello,
In addition to previous ticket I have further queries. I have a stringent requirement for reduction of Current consumption.
https://devzone.nordicsemi.com/support...
Hi, I've got a quick question here about using the GPIOTE driver in tandem with the GPIO HAL . For simplicity's sake, I'm using an in-house library that gives me high-level...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
I built this ( devzone.nordicsemi.com/.../Nordic_2D00_Thingy52_2D00_FW_2D00_master.zip) Nordic Thingy SES project and downloaded the generated hex file in Nordic Thingy. Now...
Hello,
I tried to build the mesh sdk in all way.
Please help me or send me the sdk set-up which is without error.
I tried by sdk15.3.0, sdk15.2.0 and mesh sdk. Try...
Hi,
I am having problems with using BLE along with gpiote and ppi for measuring the delay between two waveforms and sending the delay between them to an app using bluetooth...
