I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Hello everyone!
I'm trying to build a project of gathering the information from several temperature/pressure/humidity sensors and sending it to one display.
Sensors will...
Hi, I've tried to set BLE power to max but an app error is raised when I use the sd_ble_gap_tx_power_set function. Parameters should be wrong but as far as I've read over...
How do I align UART transmission/reception with GPIO pin signaling low/high? I wanted to do this because BLE chip is receiving the Product ID & device name from microcontroller...
Hi there,
I was used IAR to compile my source, and combine with bootloader and soft device, and it was always work fine.
Now I have changed my compiling tool to SES IDE...
Hi there,
I am developing an application using an nRF52832, nRF5_SDK_12.1.0_0d23e2a and Softdevice s132 v3.0.0. The BLE part of the application involves sniffing advertising...
Hi All
On my NRF52 device I want to return my own error code after a mobile application (android) has written some data to my custom characteristic. For that I consider...
I am trying to get 2 of the nRF52840 dongles provisioned on a mesh network (client + server). (versions nRF5_SDK_15.3.0_59ac345 / nrf5SDKforMeshv310src)
I am using examples...
Hello
I'm using the NRF52832 with softdevice 132. My SDK version is 15.3. My platform is WIndows 10.
I am having trouble configuring the TWIS. I've followed the instructions...
Hi,
Here's the setup I currently have: nRF52840 SDK 15.2.0 s140 6.1.0 softdevice Secure Bootloader pca10056_usb
I'm trying to update the mbr_params_page (0xFE000) from...
I am new to the Nordic stack, and I have developed an Arduino outdoor prototype using an nRF52840 communicating with another ESP32 (BLE + WiFi) gateway. The project is used...
I use timer+ppi+pwm model.my init code like this
I use some code to close and open PWM ,like this
question:I use oscilloscopes to check PWM, I find that when I start...
Hi all, I want to work with Coded PHY on Bluetooth 5. I tried to change lines on mesh_adv.c file like below, but i getting this error : app_error_weak.c, 119, Mesh error 7...
Hi,
I modified template example and now I am trying to add usb cdc. The applicaton results in Fatal error .I found that nrf_drv_clock_init() works fine but nrf_drv_clock_lfclk_request...
Hello,
I am having difficulty getting the AT Host operating on the DK. I have DK version 0.8.5 and updated my libraries from github (in anticipating of evaluating the GPS...
I want to handle at command in main.c file. How can you do it?
For example, how can you send "AT+COPS?" and received return value?
I tested simple_at program below, but...
