Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
Dear Nordic Team,
Thanks for supporting.
Now i am try to interface(TWI) MMA8453 with nRF52810. Already i am worked with nRF52832 its working good. If possible for interface...
I tried to add a BAS service to a project with an LBS service (ble_app_blinky), but I cannot complete the services_init() procedure for both services.
Is it possible to...
Hello,
I would like to kwno if it is possible to get information about the hardware in my main application. NRF_DFU_HW_VERSION is stored in the DFU and is used to verify...
Hi all
I want to stream data from various nRF52 objects to a single Android smarphone.
I have no problem in evaluating the throughput of each nRF52 device to the client...
Hi,
I want to set up a demo bike speed and cadence transmitter. I am using \ant\ant_plus\ant_bsc\bsc_tx source code. However, I have plans to use BLE at the same time...
Hi,
Are softdevice's api calls thread safe (specifically speaking sd_ble_gatts_hvx ()) -
i.e. Will a concurrent call to sd_ble_gatts_hvx () from several threads corrupt...
Hello All,
I am working on nRF51822 use IAR nRF5 SDK 12.3.0.
I am trying to debug the DFU in IAR. At that time i got an error show below
I use IAR version show...
Hello Nordic, I worked in a project and there a used NRF52840-QiAA-R. For this PN , I need the latest REACH and ROHS , Compliance Certificate. Where I can download these certificates...
I work on a project, where i'm trying to connect to Chips via Bluetooth.
So i have one of the Chips in a Remote and the other in a device, where i wont to receive the Data...
When pairing with nRF Connect and nRF52 I use the Just Work mode. No Keyboard No Display.
In 4.2 (and also 4.0) the MITM cannot be used in this mode.
If I set it on the...
Hi Nordic Team
Am trying to create DFU.Zip packet using nrfutil am getting this error while creating( DFU.Zip packet) for the sake of testing secure bootloader .
Am using...
after installing the new SDK for the nRF9160.
if I install the new spm on a board that is working and it will still run the old code that was present on the board befoe...
Hello dear community,
I had a question related to the Circuit configuration no. 5 within the document "nRF52840 Objective Product Specification v0.5.1". There are two inductors...
