Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I'm using nus for the sensor works with uart 57600 baud rate.
Few munites later connection is broken. I don't know why.
Can anybody know this issue?
Waiting...
Just test SDK14.20 serial DFU demo project on Nordic PCA10040 board by USB serial.
Got below exception. Any clue for it please?
Thanks.
C:\gxf\nrfutil\nordic>..\nrfutil...
Hello,
I want to modify the NRF logging module to include the line number where the log was originated.
In the past I created a wrapper macro that called NRF_LOG_INFO...
Hi all,
I am using nRF82532 board. This board TX,RX(P0.06,p.0.08) pins connected with QUECTEL module in ZEPHYR sdk platform . Please forgive me for these basic doubts. ...
HI,
I want to work nRF52 thingy with segger embedded studio.
Is there any example code to compile and run the Project file for nRF52_thingy?
Which sdk need to use SDK13...
Hello,
I'm trying to autoconnect my device to my phone using nrf Connect app. I connect to my board selecting autoconnect flag, then insert my passkey and devices are correctly...
I programmed the 15.2 sdk (ble_app_eddystone_pca10040_s132.hex) to my 52832 radioland module.
I can see that it is identified as an eddystone with URL of nordic -
But...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
WHen trying to build I get in the linker a lot of error like this:
C:/Segger/mbOS/mbOS ex/Wizmi_Project_mbOS_empty/embOS/Start/BoardSupport/CMSIS/Generic/Output/Debug/Wizmi_Project_mbOS...
