Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi,
I am using the MCU on a board with sensors that are sampled in a very high rate (~100Hz).
I am having issues when trying to send the data with notification on more...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
I have problem flashing main program and SoftDevice on the nrf 51822 module. I have Keil version 5.24 and I am using SDK v12.3 .
I can flash SoftDevice easily but after...
Hi,
I init the UART pin with the AIN pin such as P0.05, but the program will run into __WEAK void app_error_fault_handler(uint32_t id, uint32_t pc, uint32_t info) every...
Hi Everyone
I have been trying to do some simple led blinking by generating events , however i need to do that if a button_0 is pressed for some duration.
Here is a code...
We are using SDK 15.0 and Softdevice 6.0, FreeRTOS 8.2.1
Is there a way to use softdevice and NRF_SDH_DISPATCH_MODEL_INTERRUPT?
If not, it means SDH task MUST be the highest...
Dear Sir,
I am using SDK15 and sodtdevice S132. I am testing on the kit BMD300.
I am using nRFConnect App in andoird to connect to the device and check the services...
Dear all,
I used SDK 12.3 buttonless functoin with PCA10028(nRF51422), and I occur some problem.
I did some testing as below:
case 1. softdevice+bootloader
case 2...
hi Nordic ,
I am developing an USB product with the nRF52840.
Can you can request the use of Nordic’s vendor ID in conjunction with an assigned unique Product ID?
Or...
Hi！
I read datasheet: nRF52840 Objective Product Specification v0.5. It says 52840. When SPI is master, it supports 32MSPI.
Which of the following examples can I refer...
Hey!
I'm migrating from Keil to Segger SES, is there any way to get a similar checkbox interface for sdk_config.h in SES like the configuration wizard in Keil?
Cheers...
I am a newbie to BLE and starting with nordic ble chip. I downloaded SDK 15.0.1, is there any proper document explaining SDK directory structure. Thanks
Hello,
We have received in april 2018 nRF52840 QFN packages nRF52840-QIAA-R marked as well QIAA-R-SAM.
We would like to know to which version they are related : A, B,...
