Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi
I have problem enabling gzll on my nRF51. Error diagnoses shows NRF_GZLL_ERROR_CODE_INTERNAL_ASSERT_OCCURRED (#15), every time I try to call nrf_gzll_enable();
Here is...
I've looked at the reference manual and the several forum questions asking the same question and do not understand the answers as they all seem to point to the same docs/original...
HI All,
We are using NRF52, S132 Softdevice , SDK 11.0.0.
In SPI DMA transfer, when we try to increase size of the m_tx_data greater than 254 bytes, it failed. It is working...
HI All,
I did all the things as in this post
devzone.nordicsemi.com/.../
But Whitelist is not working for me. My requirement is this, I need to add the first connected...
Hi everyone,
I must to program my device from nRFgo Studio (rel. 1.21). So I do this procedure:
I program the Softdevice (in my application S110 rel. 7.0.0);
I program...
I am using nrf51822 and I am trying to reduce the transmit range to 30 cm or less.Is it possible to achieve this. The reason I am doing this is that I will be working with...
Hi,
I want to use both SPI master & slave altogether, but when I include nrf_drv_spis.h upon compilation the following error occurs :
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
I am trying to find out the lowest range of nrf51822 but so far I coulden't find anything. Most of the time people are trying to increase the range.Thanks.
Hi Guys.
I have compiled and programmed ble_app_uart program in to a nrf51DK (pca10028-nrf51488).
I downloaded and installed nRF UART V2.0 to android 5.1.1 .But while scanning...
Hi,all.i use pwm with sdk8.1 sample (SDK8.1\example\peripheral\pwm),my question is how to stop pwm and set the pin to low level? is my code correct?
my pwm init code:
...
I've a board with the nRF51 inside and a LIS3DH as accelerometer.
I already reflashed and I want to read the accelerometer values from the LIS3DH but I don't know where...
Hi Guys,
I tried to integrate the spi master project to ble_app_uart. For that I added the missing headers from spi project to ble_app_uart. And also I added the .c files...
Hi, Guys,
I am integrating the proximity app with dfu, everything else goes well. However, when I try to update bootloader through dfu, it failed. I check the MCP log,...
