Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I am using nRF51 SDK 8.1. When I add this code:
const app_uart_comm_params_t comm_params =
{
RX_PIN_NUMBER,
TX_PIN_NUMBER,
RTS_PIN_NUMBER,
CTS_PIN_NUMBER,
APP_UART_FLOW_CONTROL_DISABLED...
Hello,
According to specification, SoftDevice (S132) supports three connections as a central. Do you have example project?
I need collect data from 3 sensors:
...
I need to setup a nRF51 dongle as a transmitter and a nRF51 beacon as a receiver. The transmitter will send a byte every 7.8 ms (128 times per second).
I am wondering whether...
Hi,
I am using the ble_gls_app provided in the SDK 8.1.
Also i am using S110 softdevice v8.0.
When i am trying to bond through MCP it is asking for a passkey.
How...
Hello everyone,
I following the exmple about advertising
devzone.nordicsemi.com/.../
It advertise a string (line 142 in main.c). I want to replace this string with...
Hi,
We have updated our code to the last sdk version (nRF51_SDK_9.0.0_2e23562) and we cannot upload the application code anymore with the nRF Toolbox on our iPad. However...
Hi there, I'm having some truble to understand how to set a synthetice 32khz clock from the 16Mhz external crystal. Right now I have the next code working fine:
NRF_CLOCK...
Hey guys,
I’m trying to send a single non-connectable beacon every few minutes in the lowest power way possible. nRF51822, SD S110 8.0, SDK 9-2. Different scenario from...
I am experiencing a fault at sd_flash_page_erase() in the sdk_nrf51 ble examples.
Softdevice 8.0.0 is loaded and is from the sdk_nrf51 bundle.
Both the ble_app_proximity_s110_pca10028...
Here is my power consumption (3.0V):
no app_pwm: 0.010mA
after app_pwm_init(): 0.295mA
after app_pwm_enable(): 0.891mA
If I do app_pwm_uninit(), power consumption...
NRF52 on-site training for today, know BLE pairing use OOB way will be a little bit more simple and safe, and then want to ask next, on NRF51822 platform have the corresponding...
I'm using a dev board based on the nRF52832.
The majority of the time the RSSIsample register returns the correct value.
However sometimes the value returned is 0x7F...
