Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi, Using the nRF9151 flashed with ncs-serial-modem v1.0.0 we are using at%keygen to generate a CSR for MQTT. I want to know how the firmware generates the private keys and...
I have and nrf5340 connected to debian system via uart. I'm trying todo a flash update via the uart and the nrf5340 is unresponsive. The MCUmgr is not getting any response...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
Hi there,
I'm using /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding/connected_cs/initiator and /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding...
Issue
How to properly wake an nRF54L15 from System-Off mode when the device receives a UART transmission, without the use of the LPUART Ready and Request lines or any sort...
Hey Team! We are developing a radio-heavy BLE application on the nRF SDK version v.3.2.4 where we use the experimential QoS Channel Survey feature. In normal operation, it...
Board: nRF52840 DK (pca10056) NCS version: v3.2.3 Goal: Send and receive raw 802.15.4 frames with a custom packet format, without using OpenThread, Zigbee, or any other mesh...
When attempting to install a downloadable app in nRF Connect for Desktop 5.3.0 on Linux, the installation fails with an EISDIR: illegal operation on a directory error. The...
As mentioned in subject,I try to study course with CMSIS-DAP,now, chip recove and flash is OK,but blocked at debug step for 2 days now.
Maybe I made some wrong config some...
Hi, I am having troubles with flashing my first code to the MDBT53V module. I am flashing via JTAG cable, from my nrf52840DK using vscode. According to my measurements the...
Board: nRF54LM20A DK NCS version: v3.2.1 Sample base: nrf/ samples/zephyr/subsys/usb/cdc_acm
Background
I am evaluating power consumption on the nRF54LM20A DK before...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
This question concerns the description of the SPI communication Electrical Specifications on page 425 of the nRF52840 Product Specification.
The values for "t_spim_vmo...
Hello,
I have a product with QSPI flash that I would like to use nrfjprog to program the flash part. However, the QSPI flash's VCC is controlled (via a FET) from a GPIO...
