Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hello,
I am working on adding MCUboot to my custom board (using nRF52832 chip) to make it DFU-able. That works fine when using internal flash but never when moving the...
Hello, I'm using an nRF9151 DK with an SPI attached SD card and SDK 3.1.0.
SD card is accessed using FAT_FILESYSTEM_ELM.
Using a single thread approach everything is working...
Hi,
We are using a TMD2636 proximity sensor on our board, connected via I²C on pins P0.18 (SDA) and P0.30 (SCL). The same I²C bus also contains a TMP117 temperature sensor...
Hi,
I’ve enabled OTA firmware updates in our project using MCUboot. Before enabling OTA, everything worked correctly—our firmware received interrupts on pin P1.00 from one...
After reviewing the nRF7002 datasheet and reference design guidelines, we were unable to find the input/output characteristics and voltage ranges for PALDO, VDD_BUCK, PWRIOVDD...
Current Setup
I'm currently setting TX power during advertising using the following code:
This successfully sets TX power during advertising, but I need help with additional...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
All of the following used the same power supply to power our development board and measure the current of the development board: The PPK2 I purchased measured an average current...
Hello,
I have connected the nRF52840 DK to the nPM1300 EVK , with the DK powered from BUCK1 output of the nPM1300.
When I supply 3 V or higher to the VBAT pin of the nPM1300...
Hi,
I’m evaluating the NUS (Nordic UART Service) as a way to stream and receive byte arrays.
I’ve noticed that there are two different implementations of the NUS service...
Affecte d SDK : n RF Connect SDK v 3.2.0 (Zephyr v 4. 2.9 9)
File : z ephyr/drivers/i2c /i2c_nrf x_twi.c
Description
The I2C TWI driver always returns - EIO for every...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
Using NCS 3.1.0 - getaddrinfo with "offloaded sockets" (nrf9160/51) and ipv6 results in struct sockaddr_in6, where some "c struct padding bytes" (the last 3 of 24 bytes) are...
I flashed the thingy91x using NRFCloud connect. Provisioned it in nrfcloud using hologram SIM cards. How do I turn on air quality and all other sensor information?
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
