Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi,
I've some questions on nPM1100's buck regulator
1) What is the Iq (quiescent current)?
2) Does it support 100% duty cycle?
3) What will happen to VOUTB if VINT...
Hi,
We are using ANNA-B112 module with nRF52832 chip and trying to store the product serial number in UICR. From the description of UICR, it seemed that the CUSTOMER area...
Hi,
A have an application on a custom board that will not start, unless I use JFlash Start Application command, or attache the debugger. I already added CONFIG_BOARD_ENABLE_DCDC...
Hi,
given "nrf_drv_twi_xfer" or its "nrfx_twim_xfer" younger brother is used to communicate over I2C, and its a TxTx tranfer, than what does "nrf_drv_flag_tx_no_stop"...
I am using bleak and python to connect to a ble device and then using subprocess to run the dfu. The ble device disconnects when the dfu starts and then I get "Connection...
I have a Thingy:91 board that appears to be broken, no response either on the LED or via USB UART when switching on.
I've earlier done some development with it, and hooked...
Hello,
I am attempting to follow along with the AWS IoT example. Everything has gone OK so far (Create a Thing, Create a Policy, Create and download certificates) until...
Hi All,
In our product we have noticed that, on a few occasions, some important information that is saved using FDS (in a file with ID: 0x02) are being erased when an OTA...
Hi,
Do you have a recommended circuit for supplying VDD_GPIO with the right timing relationship to VDD?
Section 11.1 of the datasheet says "VDD_GPIO should be applied...
Since the 9160 will vary his transmit power based on signal strength, is there any way of determining what power is being used for a given transmission? I know that the max...
The Edge Impulse firmware compiles and flashes to the Thingy53, without problem. I would like to increase the range of the BMI270 accelerometer, but can't find any reference...
I am using 52840 and SDK V14.2.0. When compiling nrf_ble_dfu.c I see the following error in nrf_dfu_types.h: line 258
"two or more data types in declaration specifiers....
Hello,
I am getting 0x07 error code when invoking sd_ble_gattc_char_values_read(..) function.
I am using SoftDevice 140 v6.1.1 APIs. I have an NRF52 dongle and I programmed...
Hello,
I am trying to send status messages to a Client model with a specific unicast address on one node. This node's parent element has both generic onoff server and client...
