hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Dear ,
I use nRF52833 to transfer audio,but I found that this audio will delay 130ms.
I didn't use 32.768K low frequency crystal, do you think this will affect delay time...
Hello!
Quick question: When a device is connected to the u.FL port (actively transmitting things to the port) on the nrf52840 board, does board (in rx mode) only listen...
hi,
program: 'ble_app_blinky_pca10056-s140'
nRF 52840 dk
keil uvision5 IDE.
with the help of IDE , i could build the code and flash the code on to the board.
but...
Hello
I'm testing nrf52820 longrange speed, but it's faster than my calculations. Will it automatically turn on the fec?
This is my config below.
m_adv_params . primary_phy...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a
Sometimes when i disconnect ble from mobile application and again connect then i...
Hello.
I'm using nRF52833, pca10100.
Can I erase only 16 bytes (or more..)?
I read this explaination , and t here's an erase page partial register, but I don't know...
Hello!
I'm currently working on an IoT device that is supposed to send data to the cloud using MQTT with a TLS layer. We got this working in Norway using LTE-M and the...
Hi,
I am supplying my nrf52840 with5V on VBUS. I know that this does not actually provide the board with power, only the USB interface.
Based on the documentation, I understand...
Hi everyone,
I have connected a potentiometer to a GPIO pin (AIN2) and would like to show the varying values in the battery service.
I was wondering if there's any way...
environment:
SDK14.2 Project: ble_app_uart
I am sure that the problem occurs in uart_module.
Uart use the app_uart_put to send the first byte successfully, then it will...
We have already developed a wireless sensor application based on the ESB protocol.
Now we want to increase the range by adding an nRF21540.
We started by testing the sample...
Hi,
Is there a possibility of race condition when writing and reading using nrf_fstorage_write and nrf_fstorage_read?
I have a very strange bug, when writing to an address...
I am using VScode's extension for nRF connect. I have been using it to flash program with the 52DK and 9160DK previously. Now under the connected devices tab nothing shows...
Hi,
I'm using the GPIO mode of CAF leds module to control led.
LED_EFFECT_LED_BLINK or LED_EFFECT_LED_BLINK2 macro can be used to set the effects of led. But the loop_forever...
I encountered problems in developing nrf5340 with nck v1.5.0.
I use nrf_rpc_tr_init(rpc_receive_handler) to initialize an RPC and IRQ_DIRECT_CONNECT(I2S0_IRQn, 0, custom_i2s_irq_handler...
