Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
So I'm trying to get to grips with the ble_app_blinky example from nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky
To start with I grabbed the hex file ble_app_blinky_pca10059_s140...
Hi, 1. In ncs v1.5.0 nRF5340 I need to drive a spi peripheral w25q128 2. How do I generate this file?
3. Where can I find the syntax rules that generated this file? 4. Can...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
Hi,
I have a custom board with nrf52840 with UARTE1 instance enabled for RS485 communication.
I have 2 boards on the same configuration and trying to send data to each...
Hello,
I am trying to use a nRF52840 Dongle to perform DFU over Thread: I am using a PCA10059 board, already provided with the default bootloader. I also programmed the...
Hello,
I am in a project using nRF52 board where I develop and Android app.
The application is using Android stock BLuetoothLeScanner to scan for devices. After that the...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. This bonding information is written to the flash area using...
So...I have an idle task running then a UART interrupt fires upon a character being sent over the serial, and somewhere during the execution of the ISR, it attempts to execute...
I am using the NRF9160DK, I have already made all the getting started and compiled an example to use the LEDs on the board with em studio. I had already connected my card...
Hello,
I am trying to send some sensor information via thread / mqttsn every 5 min. Therefore. The dongle has to wake up (5 sec.), send the information and return to sleep...
Hi friend,
I used SDK16.0 and softdevice is S140. I modified ble_nus_c to a custom 128-bit UUID. It has 1 service (0x0211) and 3 characteristics (0x0212, 0x0213,0x0214)...
Hi,
I'm testing the aws-FreeRTOS code.
In detail, It's a BLE test
The problem is, BLE can connetc in the test but next step (read/write) cannot
BLE connect apple...
Would it be possible to illustrate what AT commands would be required to set up and send a UDP packet for the nRF9160, including configuring the modem, turning the modem on...
I'm writing a program that receives a time from an RTC over TWI then writes that time into flash memory using the example from the flash FDS library. The problem I'm running...
Hi,
Am using nrf51822 as central, i want to discover and to commuinicate with the service of another ble module (which is RN4871 from microship).
My problem here is that...
