Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
I am using 2 gpio interrupts from 2 separate sensors with active soft device. one sensor generates interrupts at around 400-800 ms and the other comparatively lesser...
Hi,
So I am trying to poll the signal strength of the nRF9160 DK and at first everything seems okay, the device gains connection and all the boxes in the LTE Link Monitor...
We have added Nordic Uart Service (NUS) into the nRF mesh code and we created two mobile application.
First mobile application:
- is for nRF mesh provisioning which is...
Hi,
The datasheet for the antenna used in the dev kit, P822601, has its specification performance measured on a PCB DUT at 140 x 50 mm^2 - which seems rather unnecessary...
HI !
i have a problem during importing nrf9160 project in SES , knowing that i imported this project and others with same toolchain installed and other requirement.
onetime...
hi all
i have been working on a raspberry pi hat design and i would like feedback on it's design
this is the link to the github repo and i do update it regularly https...
hi,everyone
I want to run the DFU example in meshV3.1.0 . but i still can't understader how to run it . below is my understanding:
1.ther are must have 2 devices , A device...
Hey, i having problems with uploading code to my Thingy52.
Equipment that i using: nRF DK https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK Nordic...
Having issue with nrf52840 interface with sim808 for GPRS connection. I am trying to interface nrf52840 with sim808 using UART. But only AT and ATD command reply i can see...
Hi,
I am currently trying to test the capability of bluetooth 5 long range mode using a pair of SparkFun Pro nRF52840. I have used the blue-app-uart example and:
1)...
Hey
I am working on Bluetooth mesh. I am able to find the RSSI from server whenever i received the message from client in mesh(light switch example). Now I have to find...
We used NRF52832 to make a Bluetooth solution, but the customer wants the broadcast name of the product to be regular, and the MAC address also needs to follow a certain rule...
Hi
I have below requirement on NFC using SDK 12.3.0 and soft device S132. please suggest how to start with the same.
1.NFC operation. (Simple Read Write into NFC Tag Memory...
Hi,
I'm working on getting the DFU bootloader working and I'm following this blog post.
I'm successfully compiling and loading the bootloader to our custom hardware...
I want two pwm channel output 1MHZ frequency, the phase difference between two PWM channels is 180 degrees。when i set two pwm frequency to 500KHZ, use the configure below...
