I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi, Nordic!
I wanna know how change characteristic(service,Rx,Tx) UUIDs .
For example,
Proximity UUID : 01020304 -0506-0708-0910-111213141516
Service UUID : 01020304...
Hi,
I'm trying to merge central/peripheral example "ble_app_hrs_rscs_relay" with "ble_app_buttonless_dfu", and get error while compiling ‘ble_dfu_unbonded.c’:
I've included...
Hello I originally wanted to use esb_ptx/esb_prx but the packet could not be changed to 128 bytes! Compressing data packets is inconvenient! I use radio to achieve my project...
I am using Segger Embedded Studio and the nrf52840 development kit.
I can run the BLE peripheral examples using SDK 15 and s140 V6 "blinky" and " cscs" .
but the ble_app_rscs_pca10056_s140...
Checking if this is possible and how to complete.
For the ble_app_beacon example, I'm able to reuse #define APP_DEVICE_TYPE 0x02, to be #define APP_DEVICE_TYPE 0x0E, 0x06...
Hello ,
we are new to BLE
1. We make a long life temp and light sensor , just only transmit from the Nrf to mobile (one way ) , we would like :
1.1 sensor always be...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello,
For my project, I want to be notified when my device changes the value of my characteristic so i used the HealthThermoDemo example.
here is my code :
But despite...
Hi , I want to use two GPIO oin with button press hadler even . when pin low will interrupt and into handle..
Below is the code for the single key.
Thanks.
Pa...
This is somewhat of a continuation of this topic:
What does APP_BLE_CONN_CFG_TAG do?
Softdevice 132, header: ble.h: SVCALL(SD_BLE_CFG_SET, uint32_t, sd_ble_cfg_set(uint32_t...
I'm using RFduino that utilizes nRF51822. I need to set a timer1 as timer0 is used by the BLE stack, so I used the following code:
#define TRIGGER_INTERVAL 1000 // ms...
Hello,
Today I had a case where I tried to perform a bootloader-only DFU on a device with a debug version of the bootloader, but instead of trying to replace it with another...
Hi Technical team,
I want to use nrf52832 for my project, below are the some doubts i have with nrf52832
1) nrf52832 will act as HUB and receive data from peripheral...
Hi,
I have already working code in nordic sdk 13.1 with eclipse. But we are move to latest sdk v 15.0 for example of central and peripheral. Now every thing i have modified...
After a node successfully provisioned in the Mesh Network. If I want to unprovision the node, what procedure is needed to make it?
Should I remove all the netkey, appkey...
