When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and Master Control...
On the product page: www.nordicsemi.com/.../nRF-Connect-for-desktop
The link from the ' Documentation ' tab is: infocenter.nordicsemi.com/.../nRF_Connect_intro.html
...
Hi,
I have done BLE tutorials [BLE Advertising, Ble Services and BLE Characteristics]
With my NRF51-DK was working perfectly the example of BLE Characteristics (with...
Hi,
I designed a pcb using nrf51 chip with some sensors,
this pcb should read ,every minutes, all values from sensors and saves them into the flash memory beside that...
Dear
Now, I need make one nrf52832 board as USB Dongle, it can be HID device by checked from PC.
And, nrf52832 should support esb protocol, now for esb, I know something...
hai
i was started a bluetooth based project. So i have started with a blend micro.But the range of communication was very short.So i have chosen ble nano with TX power...
Hi
I am calculating the power consumption using
devzone.nordicsemi.com/.../
But there is some point that I don't understand.
When the BLE event type is "Peripheral...
Hello,
the past week I am trying to make the bootloader_secure example work for a custom hardware with no luck. This whole procedure give birth however to several questions...
Hi
I am currently working on a BLE based hardware but I am a little confused about the terms such as service, characteristics... etc.
Let's say, I would like to control...
Hi,
I am using the following function to read the content of a register:
static ret_code_t read_reg(uint8_t slave_address, uint8_t register_address, uint8_t *value)...
Hi,
Could you please help me identify the file and function name that is used by the S130 softdevice to start HF clock automatically for ble advertising? I can see that Clock...
Hello again,
I'm working with the ble_app_hrs example application with DFU app support. I'm following the DFU procedure and I've reached the point where I actually start...
Hi everyone,
My idea is:
I have several nrf51822 ble devices and I want to connect them simultaneously one by one with gateway over IOT. I am using bluz gateway shield...
hi all,
I use nRF52 SDK11 with ble_app_beacon example.And write some code in main().
uint8_t buf_data[32];
unsigned char c_data[] = {"abcd"};
//unsigned char c_data...
