Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I have a BLE peripheral application based on the nRF51822, running Soft Device S110 with SDK 8.1.0. The centrals are mobile apps, one on Android 5.0, one on iOS 8.4.1.
...
I'm using the UART driver (drv_uart.c) provided with the nRF5 SDK 11.0.0 on a nRF52 chip and once a NRF_DRV_UART_EVT_ERROR event is received, the receiver seems to be stuck...
Hello all!
I'm researching Radio Notification. I had read define and tutorial . But, It don't make me clearly.
Could you explain more deeper about Radio Notification...
Hi,
I just upgraded the SEGGER RTT source files from V4.98e to the new V5.41b for a nRF51DK project using gcc/Makefile. When linking the (now quite large) program, I got...
Hello,
I am using S110 8.0 soft device and using the example Nordic_UART. I am able to compile the project file in KEIL and flash it onto my board. I don't see any errors...
We are using the low power comparator on NRF51882 RayTac Module (Vcc=3.3V, Vref = 4/8), with which we are making a precise high impedance measurement!
I found some documentation...
I've been sending various BLE addresses to the nRF51 and am getting some inconsistencies of what addresses are being deemed valid.
I am using BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
I am using uVision 5.18a with MDK-Lite ARM toolchain and I downloaded nRF examples for SDK 11.0.0-2.alpha with Pack Installer.
Then I tried to compile " /ble_peripheral...
Hello everyone,
I would like to know, if it is possible to send data (power data) from a NRF52-DK to a Garmin Display Device. Do you know any application, project example...
I wanted extract BLE_GAP_AD_TYPE_128BIT_SERVICE_UUID_COMPLETE that i receive while scanning and compare it with 128 bit service uuid that i defined.
i have seen how ot...
Hi,
I am trying to debug my code in Eclipse using J-Link.
Whenever the code executes vPortStartFirstTask() in vTaskStartScheduler() the debugger stops and I can't debug...
Hi,
is there any simple way to obtain current PWM value if nrf52 PWM module is used to produce complex waveform from RAM array? The task is to get currently settled value...
Hi there,
I am new with nRF52 using SD332 and ANT+. I would like to ask if the nrF52 with SD332 can be configured as ANT+ central and ANT+ peripheral in the same time....
I have a query that is similar to the question below
https://devzone.nordicsemi.com/question/44424/how-do-i-switch-the-target-from-a-nrf51422_xxac-to-nrf51422_xxab-in-keil...
Hi,
We are currently considering the packaging design of a device which will use a nRF52. During housing assembly, the populated, but unpowered, PCB will be exposed to...
