I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello,
currently I'm migrating a project from connect SDK 2.6.0 to 2.9.0. After some changes according to the migration guides the project builds fine and also runs.
As...
I would like to use nRF52832 DK to test Nordic UART Service (NUS). But west build failed with the following messages. What is meaning of "zephyr_pre0.elf section `noinit'...
Hello,
I am attempting to use the nRF7002EK shield with my nRF54L15PDK development kit.
I have custom code, but it's based on the wifi scan example provided by Nordic...
Hello,
I would like to know if there is a way that I could see the source code of the nRF Mesh Sniffer app for Android, just like the nRF mesh source code is available in...
Hi, I am currently using the nRF52832 MCU and have implemented hard fault handling as follows: I use the macro APP_ERROR_CHECK(err_code), which, in case of an error, calls...
Hi
I am trying to perform a full modem update on my nrf9160 DK board.
I started at v1.3.4 and successfully used the partial update method to go to 1.3.5
I then used...
Hi everybody, I'm looking to build a PWM generator with 2 outputs from 1-100Hz. Unfurtunately the current PWM API examples with Zephyr works only for 4-100Hz.
I've tried...
I am using ncs sdk, my projects are under ~/zephyr-workspace. This is from an example project - blinkypwm. The clangd compiler shows the following erro: In included file:...
I try to simultaneous update (app + networkcore) with usb and external flash on my custombord And serial recovery, not DFU from app.
this is mcuboot config. I have set the...
i want to commission matter compatible smart switch into thread network.
but i'm getting internal error .
but other device like matter samples light_bulb (nrf52840dk)...
Dear Nordic Support Team,
I am currently using the nRF52840 development board and working on developing a dimmer switch. During the development process, I encountered a...
I just downloaded the latest version of nRF Command Line Tools: nrf-command-line-tools-10.24.2-x64.exe
My desktop is running Windows 10. The installation is successful....
Can you supply Ubuntu docker image to me to build matter project(ex: bulb)?
Pay attention to my Ubuntu server is offline, so it need to whole docker image, all I need to...
Hi,
I'm porting an application from nRF5 SDK (v16.0.0) to nRF Connect SDK (v2.9.0) to be able to work with the nRF54L15. While porting our ADC functionality, I noticed that...
