Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
Hi community,
I'm making a custom board using the NRF52840-CKAA. I'm trying to make a Bluetooth application for this board but struggle to achieve it.
setup:
- Visual...
nPM1300ek version: 0.9.0 I have both "nPM Controller" and "USB PMC" USB connected. I tried powering USB PMC through the computer and also tried a "Wall Wart USB".
I have...
Hi,
I have a device which has different UUID s for the write and read characteristics than the Nordic devices. The device I want to connect to will give out sensor data...
hi,
I am in the process of creating a board definition for a custom hardware we are proptotyping. I follwed the instructions in the intermediate course, copying the nrf5340dk...
I have a device which advertises some services, I want to discover those services and write to those characteristics. However I can only find one service and not multiple...
Hello,
I want to send audio to multiple headset(Readily avaiable from market), So is there any hardware, Software solution avaiable for that.
So, Is there any...
We've had good success measuring power consumption with the PPK2 until now. But recently, it started reporting some hard-to-explain numbers. Specifically, t told me a nRF9160...
Hello everyone,
Im currently using the Thingy:91 with the asset tracker v2 application. As I understand the default mode in this application is the passive mode. Im measuring...
Is the nRF52840-CKAA port impedance for the various transmit power settings (or at least for 8dBm) available?
Alternatively, is the expected port impedance, when viewed...
Hello,
I am building basic board on nRF5340(based on Raytac MDBT53 module) and after "Erase" operation in nRF Connect Programmer I cannot access chip anymore.
Board...
Hi all,
I am working on Fantel BT40F which uses nrf 5340 soc. I have finished my breadboard testing phase with the development kit and now I am working on Integrated pcb...
Before adding ubxlib module repo into nrf/west.yml, I can build any project with mcuboot with no problem.
However, I cannot build any project with mcuboot after adding the...
Hi,
I'm stuck in the loop of calibration. This is the error that I get from Putty:
It says that I get a TX error.
This is the code that I have for bno055.h:
This...
I used C:\ncs\v2.6.1\zephyr\drivers\adc as an example for testing adc, the following code has been added to nrf9160dk_nrf9160_ns.overlay
I applied voltage to pins p0.13...
I'm trying to test the RGB led on the thingy53.
Using the sample: C:\ncs\v2.6.0\zephyr\samples\basic\rgb_led which gives errors about the devices error: '__device_dts_ord_DT_N_ALIAS_red_pwm_led_P_pwms_IDX_0_PH_ORD...
