I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I am new to the NRF and private-public key pair using.
Can anyone please explain me how to use custom keys for MCUBoot, I added below config in /child_image/mcuboot...
Hi all
We are using ztest in our project because it works nicely together with twister, Zephyr's test runner tool. We need to have the ability to mock modules. For this...
Hi Team
we have NR52833 ,NRF52 these boards Serial no : 10001208 , 10001220
we use these devices in wipro BQTF as reference devices and not for any production. We are...
Hi
I read this Q&A: How to configure the P0.00 and P0.01 pins as GPIO , which is similar to my question. There are some things I did not get from that section:
"Physically...
Hi there, I am trying to do a blocking simple ADC measurement in using NRFX drivers in a threaded context, however when I build I get the following error:
gen_isr_tables...
Hi,
I am using nRF9160DK v0.9.0 with Cellular Monitor 2.4.0, and I have flashed AssetTracker2 via the "Program device" button.
Although asset tracker works fine uploafing...
Hi,
Using the nrf Connect Programmamer v4.2.0, I get the following error when connecting to J-Link on some of my custom boards (about 30%):
When I run nrfjprog...
I am attempting to enter a sleep state (System Off) with a wakeup button . I set all of my GPIO pins to the default config except for my wake up, configure the appropriate...
Hi
I am unable to get the Guiconfg to work in lesson 1 exercise 2 of the nRF Connect SDK Intermediate course.
I have attached snap shots of the output when I try to run...
I'm using the custom board of nrf 5340 with 7002.
When I run the sample project of Hello World, the current is about 90 ma,
and I run the sample project of WI-FI Scan...
We are going into sleep mode for the processor. We are using Zephyr and sdk 2.3. We also are keeping a running count of seconds and synching that once a day with a modem....
Hello,
I'm working on a product using the nRF9160 and facing challenges with poor LTE signal strength, leading to significant power drain when the device goes offline. I...
I was pairing using nRF connect app via mobile phone and I noticed that there's a check mark which says "PIN contains letters or symbols":
Is there a pairing method which...
