I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
nrf-programmer app fails randomly ot upload image using SDFU to pca10059 target, I have to repeat process several times to get job done.
Version 3.0.4, OS Debian GNU/Linux...
Hello!
We are using a custom nRF9160 board with 3 differential ADC channels. The differential voltage is measured across two resistors, with the center voltage (normally...
Nordic Team,
I have a question regarding RTC1 with regards to app_timer2.c
My Setup: nRF52833 - PCA10100 Development Board nRF SDK v17.1.0 s140_nrf52_7.2.0
What am I...
Hi, I'm working with just one NRF5340 audio DK and I saw this ticket where it was commented that it is possible to reduce the use of 2 NRF5340 audio DK's to just 1 using a...
Hi,
I have one central and one peripheral devices running. Currently I run a scanning filter on Central side and connected to the peripheral with desired name.
But now...
I was trying to follow the instructions at https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52_gs.html#connecting-to-the-application for testing my nrf52840...
Hi,
Using Windows 10 and SES
SEGGER Embedded Studio for ARM Release 6.34a Build 2022083102.51023 Windows x64 2014-2022 SEGGER Microcontroller GmbH 1997-2022 Rowley Associates...
Hi all,
I want to ON and OFF advertise manually
My code working steps
1) (APP_ADV_DURATION 3000 ) after this seconds over
2) It hits on_adv_evt() function in this...
Hi All,
I am using asset_tracker example V1.8.0, it's working fine with nrf9160DK. I am able to see the data on nrf cloud.
The purpose of testing this board was to debug...
I am working on two devices, a peripheral and a central. The peripheral is custom hardware. The central is being run on a Rigado BMD-300 series evaluation kit. I'm using Segger...
Hi,
Perhaps this question is too basic, but I haven't been able to find this anywhere.
I've followed this tutorial successfully with an nRF52832 DK:
However, I'm missing...
Hello,
I wanted to create an SPI shell, similar to what is available for I²C. I am therefore trying to create a generic SPI device in the devicetree:
Somehow I am...
Hello,
We use nRF52840(0dBm)+nRF21540(Dec6).
In the case of using nRF52840+nRF21540, tx spurious emissions occurs severely in the nRF21540 output.
FEM(nRF21540) output...
Hi.
I am developing a custom board using the NRF52840. The mcu needs to connect to a modem and a gnss module. Both modules will communicate with the mcu over UART
I'm...
