Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi!
I use XMONITOR to get the current cellid but it seems strange.
%XMONITOR: 5,"","","24008","2725",7,20,"01ADF70B",215,6400,50,35,"","11100000","11100000","01001001...
I'm working on nRF9160-dk.
I built a sample application "serial lte modem" in NCS 1.6.1.
i can use AT command on the UART0, but i find the printk in source code is not...
I have successfully compiled my project using `west build` and now I am trying to load it onto my nrf5340 board I recently purchased. Here's what I'm doing:
- From the same...
Hi,
I would like to test some environments. Therefore - I would like to use an example from SDK 17.0.2, which allows me to connect to a PC via NFC, as a peripheral, receive...
I'am working on nRF52840-DK and nRF9160-DK.
i'd like to add an interrupt pin for a SPIM device. (eg. in the following spi_dev: )
&spi3 {
compatible = "nordic,nrf-spim...
Dear nordic team,
i want to take log from dfu example i tried using rtt veiwer but it doesnt work.im using sdk version 17.0.2 and soft device 7.2.0 and nrf52840 DK
in...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE command using application. How to do that? I tried to assign the variable...
Hi,
I’m using the nRF SDK 1.6.0 and trying to build the “ memfault ” sample for nRF9160 using the
“ nrf9160dk_nrf9160ns ” board. The sample location is:
C:\Users\username...
Hello, after I make the connection to the nrf device with the phone, I found there is only a "Forget This Device" option on its setting page. So is there a method such as...
Hi Nordic,
The bluetooth qualification needs the information of nF5340's value n for Intermodulation test but hard hard to find in any document.
Please help us out, thank...
Hello,
It appears that when the project is generated it is expecting a "../common" directory?
CMake Error at /opt/nordic/ncs/v1.7.0/zephyr/cmake/kconfig.cmake:209 (message...
Dear Sirs,
after "few" hours of testing, I noticed that nRF9160-DK loaded with SLM v.1.6.1 is not working the same after awakened up from sleep (#SLEEP=1) or even from idle...
Hi everybody,
I have developed a project where a central device with multilink, connected to the maximum peripheral as much as is possible (in my case 4 devices more). ...
Hello,
I'm trying to figure out how to get A-GPS data via a GSM modem in places where LTE-M is not availalble.
Does the SUPL library support this, if I populate supl_client_ctx...
Hello all,
I just found out that the nRF Connect extension for VSCode has been release, which is great news. Good job Nordic Team! I have followed the steps described in...
