Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We communicate with another microcontroller (a STM) with I2C. The nRF52840 is the master...
I want to use the Direct Test Mode software in the nRFConnect App for radio testing on my custom board, but it's not working. I suppose this is happening because I connect...
Hey all
I'm working on a BLE device using a nRf52840 SOC and for some tests now I've to measure the RSSI on a specific BLE channel (e.g. ch 37). What I've done so far...
Hi
I am using NC version 1.5.0 Dk version 0.15.0 .I am trying to get the AGPS data ..it's working sometimes and some times I'm facing the following error.Can you please...
Hi,
Is it possible to run a freeRTOS project on nRF52805?
I've follow the instructions from "Developing for the nRF52805 with nRF5 SDK" on the simple "blinky" example...
Hi,
I want to know a few things about sending large packets via BLE using nRF52 SDK 15.0 and above.
I am able to send the packets larger upto 128 Bytes. But i want to...
We are working on our development board contain the nRF52840. We also use Bluetooth Low Energy to load wirelessly the updated code with the DFU and it's working properly....
Dear Sir/Madam,
We are planning to devellop a remote control for resque equipement.
The remote controller and the host should pair 1 to 1. Pairing should be easy for the...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0.
I...
I am working on zigbee network where I wanted to get the tree of whole network but could not find any utility from nordic which can provide those info, so I have started developing...
Hi,
In my application, I'm trying to restart emulation because I want to switch from the NDEF static payload mode to ISO-DEP mode. The problem is that when I stop emulation...
Hello guys, looking forward to some help here!
I've been working on a Unit Test system setup with CMock + Unity for a BLE app. But when I try CMocking some headers in the...
Hi everyone,
I want to set TX_POWER using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV,m_adv_handle,RADIO_TXPOWER_TXPOWER_Pos4dBm);
m_adv_handle = BLE_GAP_ADV_SET_HANDLE_NOT_SET;...
