Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hello, we are having a low occurrence issue when attempting to write some data in NVM using fstorage.
We are using a nRF52832 as a BLE peripheral using SDK15.2.0 and SoftDevice...
Nordic colleagues,
We just received our nRF 52840 DK and are attempting to install the nRF Sniffer application to use with Wireshark. We were able to program the DK with...
Are there any plans to expose a raw packet interface for the nrf9160? And ideally forwarded via an async serial port, perhaps as an option for the SLM application? i.e. without...
Hello,
I have a problem of reading GPS options for "NRF_SO_GNSS_POWER_SAVE_MODE"
This is the code:
I always get -1, and errno value 22. This function works for ...
Problems encountered in nrf51822 software development: When burning the program to the microcontroller, I used the Bluetooth serial port service to send the collected adc...
I'm working on a prototype currently using the nRF52840 dongle. I've used the ble_app_blinky as a basic, and added some custom code to it. The goal is to use BLE in the end...
Hello everyone,
My empte memory is displayed as EE instead of FF after i cleared the memory.
I use commandpromt to check memory:
nrfjprog --qspicustominit --memrd...
I am sending a data packet by notification that spans many MTU sizes. So I do a loop over the sd_ble_gatts_hvx(m_connection_handle, &hvx_params) method until I get a BLE_ERROR_NO_TX_PACKETS...
Hello. I'm having an issue with nrfjprog that has been discussed in this forum several times but I can't manage to get it working. I'll link some of mentioned posts at the...
I use AT%XVBAT command as the power query of the device.Now when the voltage is inquired, the return value jumps and the measurement is inaccurate.During this period, there...
I have a design using nRF52832, and I'm hoping to use RAM set before a pin reset is applied. But, at least with a debugger attached, RAM appears to be randomised through a...
Hi,
I own the nRF51 dongle. I download the Keil toolchain and the nRF SDK (12.3.0 as I read, this is the last to support the dongle). I'm trying to build the ANT+ HRM RX...
Hi,
I am new to Nordic products and I cam acroos the nordic nrf 52840 pca 10059 ; however, I am unable to find any exmaple codes for PCA10059 and could anyone tell me what...
