Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
Softdevices have several separate version number systems:
a) the human-readable release version - used for hex file naming.
e.g. s110_nrf51_8.0.0, s120_nrf51_2.0.0
b...
Hi! I use a smart beacon kit (rev 1.0.0) and I would like to know how long the cpu is blocked during the data transmission/reception. I set the connection interval to 10ms...
We are designing a nRF52 based circuitry based on "53.2 Schematic QFAA QFN48 with DC/DC regulator setup"
In the reference diagram, there is an Optional block for the LFXO...
Hey all,
I've created HIDs using USB before which require a vendor ID (VID) and product ID (PID). Are these necessary when creating a device that uses HID over BTLE? If...
Is it possible for nRF52832 to drive an SPI TFT 240x240 LCD and a TWI Capacitive Touch Panel with BLE and NFC? Is 64Mhz the highest speed?
What I mean is that is it possible...
I am creating a project which must use two spi at the same time , the one store data to flash and the other use to communicate with FT221 .In the datasheet ,I realize that...
Hi Devzone,
We are currently awaiting arrival of our custom board, based on the nrf52 chipset, and I've been tasked with determining any potential gotchas with programming...
Hello,
I am trying to implement a star network with more than one datapipes enabled, where (between other tasks) the PTXs devices have to synchronize their clocks (real...
Hey, I am compiling some code to both read ADC measurements and send the measure it over UART. I looked at the ADC+UART+SOFTDEVICE example on github and I think I am pretty...
Can you please provide me the iROM and iRAM settings for the S110 softdevice for the nRF51822? Specify the SD version you are using please.
I'm reading nRF51822_Development_Kit_User_Guide_v1...
hi
i get vlaue with this line of code
but i did not specify what char should get it value
how can i get value from specific char?
i have nrf51422 v2 sdk v6
hi,
Everyone,
I was just checking on nrf51422 Dev kit for LFCLK and HFCLK oscillator configuration.
with lfclk set to start external oscillator ,it does not start external...
