Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I use the bootloader in SDK v5.2.0 and could not run APP after DFU completed.
It always stay in the DFU state.
After checking the memory by J-Link commander, something...
At work we are primarily interested in using the 128kb nRF51822 devices. I am able to get a softdevice and bootloader onto a 256kb device just fine. When I attempt to do the...
Hello all,
I want to send some sensor data( collected by Pic controller) to other BLE client(may be a phone) using nrf51822 via UART. Can somebody suggest how to communicate...
Hi,
In the reference design of "nRF51822-QFAA_ST_BAL-NRF01D3", the datasheet recommends this crystal ( www.digikey.com/.../3125558) , but we are out of stock from local...
Hello all,
I have flased "ble_app_hts" example for nrf51822 on evaluation board PCA10001. In the application both the LED pins are configured for output using "nrf_gpio_cfg_output...
I have a large array of uint16_t data to use as a lookup table, which is defined in flash. It's 4002 bytes in size, and I can set where in flash it is saved. I'm accessing...
I am using an nRF51422 and attempting to interface
it with an MPU9150/6050 using your MPU6050 driver and
the underlying twi_hw_master.c.
I have modified twi_master_config...
Hi all,
My application gathers sensor data and uses the advertisement packet to broadcast the values (much the same as the nordic temp sensor example). Rather than having...
Dear developers,
I need to turn nrf8002 to master mode in order to use Alert Notifications of "Profiles - On Master" offered by nrfgoStudio. I need these profiles to activate...
I'm trying to send data acquired from the ADC and monitor it using the master emulator.
The values I'm getting do not appear to make sense though.
I'm using the BLE_HRS...
Hi,
Original UART DFU bootloader SDK example ported from NRF6310 board to PCA10001 board does not work.
What did I do wrong - can anybody please help me ? Thanks in...
It's possible this is a hardware problem, but what I'm seeing is this...
The clock is enabled on pin 0, data on pin 4. With both enabled in exactly the same way, drive...
Hi, I am trying to get the rssi value of a connection, and what I am trying to do is to start the rssi in the beginning at the connection and end it at the end of connection...
Using S110 version 6.0.0, Sdk 5.2.0, GCC 4.8 (C++, but that don't matters here).
I want to know, if the central has switched Notification and/or Indication on or off for...
