Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs
but:
1.How does the client receive those data?
2.How dose the client send data to server...
I'm totally new to Nordic, ARM development, and the mbed platform. Not new to embedded development however.
So far I can't get the simplest possible program to run.
...
I just received my nrf51822 dev kit and noticed that the SWD debugging cable will only connect to the PCA10004. The PCA10005 that came with my kit has pin 2 missing, rather...
HI,
I wrote my application based on "MasterEmulator->ProximityDemo" for testing device with nrf51822. My device have to switching between Gazell and BLE stacks so all the...
Hi
In ble uart project, the data is used string format. Now, we want to modify uart apps to tx/rx binary format. Could you tell us how to modify the uart apps? Thanks.
...
I added a local service with a characteristic with the Notify permission set.
On the device I'm connecting from to the nRF8001, I can see my custom characteristic has a 0x2902...
I'm designing what is essentially a small beacon board built around an nRF51822. On the antenna outputs I've used the discrete component balanced to unbalanced circuit shows...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
nrf24LE1 external interrupt is not easy to use , I use nRF24LE1 48pin chip, and the external interrupt 0 (GPINT0)is configured to falling edge trigger, but it can not be triggered...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
