Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi
I recently had to bring some prototype boards online for the first time, and in this context did i have to flash the modem firmware (v2.0.2 to the SiP (nrf9151).
...
Hi,
I have been debugging with Serial LTE Modem(SLM) without an external flash .
I made the circuit of nRF9160 (SICA) without the external flash (MX25R6435F?) , I would...
Hi All,
I am using nRF Connect SDK v2.7 + VsCode + NRF5340 DK and trying to add and extend matter-light-bulb sample. With ' MA-onofflight ' when I try to compile the project...
Hi,
I am working on nrf52840DK with NCS v2.7.0. I want to send the data to the addressable led strip using the pwm interface.
I am using the NRF PWM driver ( nrfx_pwm...
Hi there
Does anybody now if there is a implementation / reference project / company which solves the firmware over the air update of several devices inside a OpenThread...
I am having nrf52833 module where I need to update the firmware via uart, I am using sdk_16 and I'm unable to find the PCA10010 for uart. Can anyone suggest me how to attempt...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
SDK v2.7.0 nRF5340-DK with nRF7002-EK Matter samples (e.g. light bulb) Extra CMake arguments: -DSHIELD=nrf7002ek Use sysbuild
Tested with v2.6.2 (no sysbuild), and it...
hello ,
some brief about my board it is nrf ble nrf52810 without crystal.
i am using segger debugger.
while doing step by step execution it come till line sd_softdevice_enable...
Hello！
I am using the development board of NRF5340DK, I found an external flash (MX25) on it, I want to know how to program the external flash through the onboard jlink...
Hi, our design makes use of nRF52840 MCU. Power is supplied to VDDH pin from a Li-Po battery which can range from 2.5V to 4.2V. Internal REG0 is used to regulate voltage down...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
Hello,
When I upload the Matter Weather Station application to my Nordic Thingy:53, I encounter a problem.
I am trying to use Google Home to read sensor data, such as...
Hello, I have a custom development board using the 52840 chip, with two LEDs and a serial port connected. It worked well when developing with nrf5 previously. Recently, when...
