Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi folks
We are facing an issue with occasionally ~240 uA added current consumption on our nRF52832 based custom board when it comes out of reset. We only see the problem...
Hi all,
currently, I'm using NCS 2.4.0 with nRF9160 board (custom board).
I'm facing issue once enabling CONFIG_TFM_PROFILE_TYPE_NOT_SET.
The issue is bootloader won...
I'm working with nRF Connect SDK (Zephyr). In that I am using 255 byte array to get response from nrf52832 through BLE. my code is getting crash in response back. when I decrease...
Using the nRF52840 with NCS v2.6.1, I want to put the device into a low-power sleep state during idle time. Before sleeping, I configured a GPIO interrupt as the wake-up source...
Hi everyone. I'm trying to read data from an MS5611 pressure sensor using the nRF52840,
but the I2C communication isn't working.
Upon checking, I noticed that the I2C...
I have a board with an nRF9151 device on it that was provisioned to the nRF Cloud under one User Account.
I would like that device to be in a different User Account, and...
Hi,
I'm using nRF connect extension with VSCode and developing for Actinius Icarus IoT board (which uses nRF9160).
Even when building the example code of hello_world ...
I tried generating sec_tag using sys_rand32_get() or other arithmetic method during runtime. All 3 certificates (CA, client cert, client key) were able to be written into...
I want to compile the ble_uart example using Segger Embedded Studio. I installed today the latest version V8.16. I am using nRF5_SDK_12.3.0_d7731ad.
I imported the project...
Hello,
I'm trying to change the name of the USB port in the "usbd_ble_uart_freertos" example code. Currently, it shows up in the Device Manager as "USB Serial Device (COM12...
I am developing a simple BLE mouse using ble_app_hids_mouse of SDK17.1.0. I found out through devzone that left mouse button click sends (1, 0, 0) and right button click sends...
I'm unable to load values into characteristics—they show up as N/A on the nRF Connect app. I tried to enable notifications using the Client Characteristic Configuration, but...
Hi Nordic Community I have a problem with the PAwR examples were I'm unable to place a sync interval bigger than 2 secs.
The example starts with an interval of 0xFF * 1...
I am working on firmware that acts as a BLE sensor hub to pipe BLE data from connected sensors to a PC over USB (using the CDC ACM UART interface). The peripheral sensors...
Hi team,
We need to interface STM32L4(Host MCU) with WT02V40V in our design.
Is UART communication enough for interface both?
And also, Is CS pin common for SPI and...
