The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I am working on a module MS12SF1(nrf7002 + nrf5340) module. I am getting uart data from another device to this device through uart. Earlier when I configured uart to its by...
We have some custom hardware that acts as a peripheral, and currently has the advertising data packet set up as follows:
BT_UUID_SPD_SERVICE is our custom 128-bit UUID...
Hi.
We moved to version 2.5.2. Here we encounter some problem with data mode. Sometimes we don't get response of exit from data mode.
We publish data, after we send "...
Hello Everyone,
I wanted to ask if there is a way to use SonarCloud for analyzing a firmware based on the nordic toolchain v2.5.2, I understood that I have to set up the...
The MDS service supports the chunks through Bluetooth GW. in reality this is not of much use in real scenario. So is it possible to upload the chunks directly to memfault...
I am running the demo of "nrf-knx-iot/samples/light_switch_actuator" on my customized board based on NRF52840.
I could burn the light_switch_actuator firmware into this...
I posted my configuration in a separate discussion .
Calling this method works when CONFIG_BOOTLOADER_MCUBOOT=n works. But as soon as we flash an image with MCUBoot enabled...
Hi Support Team
We add below code to the while loop in the main.c file of NCS sample https_client to post data to server. But it can not recover to post data to server...
I'm trying to import the native libraries to Xamarin forms, I need for the FirmwareUpgrade section of the iOSMcuManagerLibrary. I compile the example project correctly and...
Hi,
I'm using the NRF52805 with the QDEC.
As far as i saw in the datasheet, the QDEC suppose to take about 5uA But when i operate it is takes about 500-700uA !!
...
Hello,
We need to use some fixes that aren't released yet in a version yet. Specifically, an MCUBoot fix: github.com/.../303
Is there a guide as to how to use forked version...
If I purchase a Zigbee endpoint device off the shelf (for example an SOS button) and I added to my nrf Zigbee network(routers and coordinator and other endpoints I have developed...
Hi,
I am trying to use BLE time sync code and it seems working well with 16Mhz timer and rtc as well.
Here is the previous ticket.
One thing I noticed is about...
As shown in the above picture, 1. Choose 10000 beat times for monitoring. Why is there a significant difference between the pulse peak and the peak of selecting 100000 beats...
Hi,
Im currently adjusting this i2s sample code to work with my TAS2781 audio amplifier. The code works perfectly but I just want to do a little adjustment on the channel...
