I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I have freshly switched to nordic and the surrounding nordic nRF Connect SDK from ESP due to a need for a low power chip with thread / matter.
I found some cheap...
Hi,
I have implemented the nRF5x-Custom-BLE-Service-Tutorial ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) using nRF5 SDK 17.1.0 on my nRF52...
Hello,
We've encountered an issue where if the ZED missed a network key update, it will not do trust center rejoin and continue to do secure rejoin Using nRF5 SDK for Thread...
Trying to west build -b nrf52840dongle_nrf52840 results in a qspi_nor flash error but the dongle hasn't defined any qspi_nor flash.
(This sample builds correctly with the...
Hi,
I want to output debug message(printk) through USB port on nrf52840 dongle. how to config it in zephyr, I have read the HelloWorld project code, but got nothing,
...
Hi,
I'm trying to make my nrf52840 dongle a ble central device. I did worked with the usbd_ble_uart example succesfully, but I was trying to add the ble_app_uart_c to it...
Isn't it supposed to autocomplete that? If I complete it to k_msleep(1000); the application builds and runs fine.
VS Code 1.67.2 nRF Connect for VS Code Extension Pack 2022...
Hi there,
We have a custom board that runs on a nRF52833 chip.
In order to flash firmware to that board, I use the Nordic DK (PCA10056), and connect my custom board to...
I've just installed the Nordic SDK version 17.1, SES version 6.3, and Segger J-Link Software version 7.64e on a new Ubuntu 22.04 laptop.
I've installed everything in their...
Hello everyone
I am using BLE Peripheral UART and Central UART samples to send data between two nrf5340 dev. kits.
I'm trying to set the directed advertising on the peripheral...
Hi All!
I am using nrf52820/33/40 devices. Able to connect central (1) and peripheral (4) concurrently.
Central is an end node(nrf52820) that is connected to the sensor...
Hello Team,
We are looking forward to use Long Range Advertisements in our application. Our current application is based on nRF52832 + ncsv1.8.0.
Per our knowledge...
Hello, We're developing an LPN product that will leave the mesh and stay off the mesh for up to 3 days (possibly more). When it rejoins the mesh, the central server/gateway...
Hello, I am currently working on the nrF52840 module with the soft device s140.
My job is to read the values from different characteristics.
The characteristics are...
