I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I am using nRF5340DK for development. Currently, I have two problems:
QS1: When I use fun nrfx_gpiote_out_toggle(), it reports Assert error on NRFX_ASSERT(! pin_in_use_by_te...
Hello,
I am working on integrating wireless-timer-synchronization into the HCI_RPMsg sample provided with nRF Connect SDK. My goal is to synchronize ADC sampling between...
Hi all,
I am using the kit nRF5340-DK, connecting to windows 11 pro. Already installed nRF Connect for Desktop 3.10.0 and nRF Command-Line Tool 10.15.4 (32/64 bit).
It...
Hi:
I want to include the Characteristic value in the advertising packet，for example the real time battery level，thus there is no need to establish a connection between...
Hello.
I wish to implement a DFU Client. One (USB connected) nRF52840 based device should update an other (Wireless) nRF52840 device.
As the SDK only has a DFU service...
I am planning on pairing two parts of my system using OOB pairing via a UART connection. I couldn't find many examples of pairing using a physical connection as oppose to...
Hi,
I use ble_app_uart sample code using nRF52840 in SDK15.
There is a code below in ble_stack_init().
And APP_BLE_OBSERVER_PRIO is defined as 3 at the top.
On...
Hi there,
We are currently doing current measurements on the nRF5340 DK with a Power Profiler Kit 2.
To do this, we simply use the PPK as a source meter and connect it...
Hello Nordic Semiconductor
I am developing a small application on the nRF52840 development kit where I need to transfer I2S signals in/out of the MCU. I have set up an I2S_IRQHandler...
I'm trying to send data readings an advertising packets from the nrf21540-dk board, and use the phone as an observer to record the data.
So far I've been able to send counters...
I'm sending a short data string from a NUS application. For some reason I cannot read the data as bytes, only string, even if the sent array is uint8_t.
Is there a specifier...
For Errata 149 on nRF52832 , TWIM send illegal pulse after clock stretching.
When using TWIS as slave device and TWIS require clock stretching,
Do they work correctly...
I have an issue with DFU via USB CDC ACM.
I would like to update the firmware using open bootloader over USB without softdevice.
I already tried to follow the thread:...
