The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all:
I am using nrf52840 hardware. nrf connect sdk.
I am using file system and mcuboot at the same time. When i call ` flash_area_open (id, & pfa);`, i got a wrong...
Hello,
we developed a proprietary protocol on top of IEEE 802.15.4 user zephyr on a nRF52833. Everything was fine with hal_nordic on commit 74b3b21f60aa3dc9a4364ffc28dbb47ad8b699a9...
When I pair the peripheral with a dongle connected to nRF Connect Desktop application, then disconnect and Connect again, the nRF Connect does not remember that it was paired...
I built the SMS sample without changing anything. I am using a Lebara prepaid sim card. I was able to exchange SMS messages from one cellular phone to another. I checked with...
Hello,
For a long range test between the nRF Toolbox Android app and the ble_app_hrs (in nRF5_SDK_17.1.0 package) over the nRF52840-DK. I would need to setup this board...
Hi,
I initiated pin 28 as SCK of SPI as normal condition, and I'd like to switch pin 28 as GPIOTE while receiving a command via BLE.
Basically this is how I achieve...
Hi,
I have loaded a simple application on my nRF52840 that just activates a GPIO as soon as it reaches the main loop.
The SoC is powered externally according to the chapter...
Hi,
We will create a ble peripheral device and also can handle timing-critical uart request. The uart will be always communicating and response time can't be slower than...
Dear DevZone:
I am developing an evaluation board with the nRF9160 SiP model, but I have some doubts with the software. Does nRF9160 SiP come factory preloaded with any...
Hi,
I try to implement Serial DFU update using the info in the " Add DFU support to your application " at link
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hi Team,
When the slave side of the SPI received data from the master side, I want to log the received data to judge If it is right. But, I want to print it by log. it can...
Hi,
I am running some tests with the long range example provided by Nordic and observed this behavior which I can't account for.
https://devzone.nordicsemi.com/nordic...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
