Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
We find a Beaocn from other distributor , it got very less fluctuations. RSSI table show below.
Test method: 10 RSSI were collected from a hand-held mobile phone at...
Typically the Base address registers and Prefix registers are used to configure up to 8 logical addresses and then RXADDRESSES is used to filter which of the 8 logical address...
Hi,
The new AT monitor have a hard-to-reproduce bug: the subscriber entry list alignment is not specified in the linker script. Since structs are always aligned, that means...
Hi,
im porting our nrf9160 application from SDK 1.3 to SDK V1.6.1. and facing error while accessing NVS device in SDK V1.6.1.
in SDK 1.3 i used "device_get_binding(DT_FLASH_DEV_NAME...
Hi,
I have have certain thread that I would like to be active during a ble connection. I can suspend it when not needed and resume when connected. But as long as the thread...
Hi:
I'm using SDK V17 & encounter a problem.
in my project, the nRF52832 doesn't broadcast at all.
Once the button1(EVK btn1) is pressed and lasting 5 seconds,
nRF52832...
I'm very new to the NRF boards. I can not find any information on the USB port (programming port). I would like to use that to read serial data written from a terminal program...
I am using the nRF 52840 development kit to explore Thread. I am using the 'open nRF Connect SDK' command to get the project. I would like to use the 'overlay-usb.conf' option...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am developing...
Hello Nordic Devzone Community,
My name is Ted, and I recently posted a question here regarding trouble when attempting to flash a Sparkfun Thing Plus nRF9160 board, using...
The connection is established but no data is transferred between the nrf52840 and the mobile phone(android10). But on android7 or android9 there are no such problems, everything...
Hi,
thanks for your support in advance.
when trying to build with example of sdk, I got the following error. it seems to be related with build env setting... please...
Hi ,I have one module designed based on Nordic nRF51822 SoC solution.But now ,I wanna use nRF52840 to make communication.I can't find the module with nRF connect app. Does...
Please don't give the usual response of 'try the troubleshooting guide' to flash the J-Link or Mbed firmware.
What I (and probably others) really need is the real initial...
