Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi we are integrating a ANNA-B112 device from u-blox that use the nRF52832 core. The pin mapping for UART appears to be different for the Software (not open source) that they...
I have a general question that I haven't been able to clearly locate in documentation. How does the processor handle "traffic" jams from within the different app timers? ...
Hi everyone, so I have been trying to enable the nRF52840 to send notifications to the Nordic Connect app via a custom characteristic. The app can detect the custom service...
Hello,
I have an issue opening the power profiler kit 2 on my windows desktop:
Somethimes it works after restarting, but stops working after a few minutes.
After it...
With a baudrate of 1000000, when i transmit 2 subsequent packets (with ACK), i have to put a delay of 0.2 msec or more. Otherwise the second packet will get ACQ packet acknowledge...
We're trying to debug an issue with our nRF52 chip when pairing to some Android phones. On the nRF52 we are connecting to mobile devices by acting as a peripheral for the...
Dear friends,
I used a serial bootloader by this tutorial Secure DFU Bootloader over Serial Link (UART) , i can upgrade my application with the pc nrfutil tool, the nrfutil...
Hi sir,
I have a question for Bluetooth 5.1 single mode. As I know, above Bluetooth 4.0 has single mode and dual mode. Single mode only supports LE and dual mode supports...
Hi.
I'm newer on Zephyr.
I want to use the LOG Output.
LOG_DBG("main.c"); LOG_INF("main.c"); LOG_WRN("main.c"); LOG_ERR("main.c");
Everything works but the color of...
Hi everyone,
I'm developing a new application/product. It will feature a nRF52805 without the LFXTAL but with DC/DC support. I'm developing with the NRF5 17.0.2 SDK.
I...
Hello,
I am trying to commission a device running the CLI sample to an OTBR I configured following https://openthread.io/guides/border-router (the OpenThread official guide...
Hi
in Zephir nrf9160dk_nrf9160_common.dts the SPI pins are defined
&spi3 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin = <19>; mosi-pin = <18>; miso-pin ...
hello,
i am using nrf52832 with sensor which uses uart communication and using sdk 15.2 but i could not get my excepted values in rx buffer which is of 3 bytes and values...
