Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi Community,
I'm a little bit flyiing in the dark, so I like to ask this in the devzone.
Does anyone already implement NFC OOB Pairing and using Apple GymKit?
1...
We are not using the USB interface on the nRF5340, and thus are leaving VBUS and DECUSB unconnected. Can we also leave D+ and D- unconnected?
Thanks,
Scott
To the kind attention of Nordic support team,
I'm interested in understanding in a conceptual way, how the microcontroller is operating when sd_app_evt_wait is called. ...
We have the following setup: - Both nRF52832 and nRF52840 chips in our product
- The nRF52832 is a module while the nRF52840 is the chip integrated directly onto our PCB...
Hi,
Kit:nrf5340
SDK:nrf connect SDK 1.5.0
1.Can you please explain how the data transfer takes place in ble mesh while using nrf connect SDK.
2. Also tell me how...
The servo I use in my application uses a PWM signal duty cycle to represent servo amperage level.
So, to measure servo amperage, I use a GPIOTE channel to capture the time...
Hi!
I'm using ncs v1.5.0 and mfw 1.3.0 on a nRF9160 DK v0.15.0.
I'm using gps sample with supl_clint_library enabled
1. Things work reasonably well, but I am confused...
I'm trying to write a driver for an SPI peripheral.
west says:
```
../ncs/zephyr/samples/sensor/mydriver/prj.conf:5: warning: attempt to assign the value 'y' to the...
new uses SDK 17.0.2, SD 7.2.0
old target used SDK 15.2.0 and SD 6.1.1
Attempting to update BL, SD, and App over DFU.
1. If merging all new BL settings with SD, BL, and...
Hi,
I am using nrf connect SDK and compiling nrf5340 examples.
I want to implement a security related example in nrf connect SDK.
Can you please tell me
1. Security...
Hi,
I am trying to open serial lte modem app to evaluate power profile on thingy91. i am using toolchain manager (v1.4.99-dev1) to open Segger Embedded Studio.
While building...
This compiles with warnings and the value always comes back as 0
#define SW1_NODE DT_ALIAS(sw1) #if DT_NODE_HAS_STATUS(SW1_NODE, okay) #define SW1 DT_GPIO_LABEL(SW1_NODE...
Hello,
I have a application on a nRF52840DK as central. The code is based on the ble_app_uart_c example.
I need to send a lot of data through UART into the serial port...
I have followed various advice to create an SPI/I2C driver an own-designed device using the bme_280 example as a model
As this could be either SPI or I2C I put both configurations...
Hi all,
I am currently working on a project which uses the ble_app_uart_c example. I have a nRF52840DK as central. The central receives NUS pakets with a average data rate...
