Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
I have built boot-loader hex file from SDK 12.1.0 secure DFU project, without any changes except for public_key.c file.
I am referring to steps mentioned under
Combine...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
My ble_peripheral is bonded to ble_central, How do I upgrade at this time ? If you still use the mobile phone APP to upgrade, you need to erase the binding information, and...
Hello,
I encountered a problem when installing nRF_connect on a new computer. As shown in the picture, the attribute "middleware" of null could not be read. Opening all...
I am using as template the MQTT sample app from NRF Connect 1.3.0, for which I want to create my own application modules, I have added the .c files to src, but I am having...
Hello,
We are using the Serial port library with two UARTEs. It defines two instances of the serial port interface: one for receiving data, and one for sending data. After...
Subject pretty much explains the problem. One can just get power from a USB interface, but if I plug our nRF52840 into such an interface, it does not appear to boot into its...
I am trying to use serialization to connect an STM32F4 to an ISP1705. My goal is too connect to other BLE devices and read some measurements. I have tried a few of the examples...
I'm using an example project of the secure serial bootloader (pca10056_uart_debug) and changed some configuration for my custom board. I added RTT debugging and changed uart...
Hi,
One of our projects will use either a LFXO or the LFRC depending on the accuracy.
The product will be exposed to temperature differences ranging from approx. 0 ...
Hello!
I handle mpu6050 sensor in SDK v14. Output of sensor values was successful. And I'm going to use this value to get the angle of the sensor.
The code below is to...
I am using NRF Connect 3.5.0 to program PCA10059 but receive the following error on some dongles when using JLINK programmer
Error while probing devices: Error occured when...
Hi there,
I purchased the nRF52 DK, and I am going to study how to use basic tools.
However, there is a problem with recognition between the computer and the nRF52...
Hello! When I start the s132 device, it freezes from time to time. In debug mode, it does not exit the saadc_init () function;
I connected "hardfault.h" and "hardfault_genhf...
