I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
The ENS210 temperature and humidity sensor connected to an nRF52832 over the I2C interface is not getting ready during initialization. During boot, the ENS210 driver reports...
Hello Nordic Team,
I am working with nRF Connect SDK v3.2.2 on the nRF54L15 DK (cpuapp) and trying to bring up WiFi using the nRF7002 together with the nRF7002-EK connected...
Hello,
I recently received two nRF54LM20-DK (PCA10184) boards and would like to flash the Matter Lock example. Unfortunately, the application doesn't seem to start. I don...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you. And to flash the latest SDK to Thingy: 91x, I need help.
Like how we can flash the...
Hi,
We have onboarded several hundred nrRF9151 devices using the nRF Cloud "bulk onboard" UI (preconnect onboarding using device_credentials_installer.py ). Generally, this...
Hi,
I have an application with 2 SPI IC connected to the same SPIM port of nRF54L15.
These 2 ICs have different SPI mode:
A: SPI Mode 1 (CPOL 0 CPHA 1)
B: SPI Mode...
Hi,
We are working on a custom design for IoT cellular communication (NB-IoT), using the nRF9151. We've done some testing with the SMA DK, and are at the stage of PCB...
Hi. I am looking into measuring radio channels' qualities by using Energy Detection (ED). But for the examples I've tried so far, I've been getting zero for all the readings...
NCSv3.2.4
Is AoA CTE supported in the nrf52811 ?
Product page https://www.nordicsemi.com/Products/nRF52811 says " The nRF52811 SoC supports Bluetooth LE, and is capable...
Dear Nordic Team,
I am working on a custom board using the nRF5340, and I have configured SPI with the following pins:
SPIM_SCK → P0.08
SPIM_MOSI → P0.09
SPIM_MISO...
I really need to verify this design for nrf54L15 SoC. If someone can go through it and confirm if it is okay or I need to make any changes ? I had made nRF52832 board but...
I am not sure if this is an issue with the nRF Connect extension or the my Thingy91 but when I use the "Flash" button in the actions tab of the NRF Connect extension to program...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
I am trying to enable the Channel Sounding feature on the nRF54L15 DK by sending HCI commands over a "USB to UART" interface. For this purpose, I created the "hci_uart" sample...
