Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I have downloaded the latest nrfgo, but the version of jlink is 5.12V.jlink5.12 does not support nrf52840,so i updata it to jlink6.40,however nrfgo still can't download the...
Hi All,
I am Using the NRF52840 DK Device for my application development
I want 2 UARTS for my application
I have used the example - nRF5_SDK_15.3.0_59ac345\examples...
I am currently developing a central device based on the NRF52832. I am able to discover and get handles to all the services and characteristics of interest on the peripheral...
Hello,
I wanted to know if I can use AT commands to communicate with nrf52840 DK.
If it is possible, do I need to have a separate firmware or is nordic sdk enough?
Hi, I am new to FreeRTOS and am planning to change to some of my code routines to FreeRTOS because my code has been expanding and in need of priorities interrupts. I face...
Hi,
I have modified the asset tracking application to work with my AWS IOT account, I have noticed that after several minutes, the broker stops responding (not getting PUBACK...
Hi,
I am experimenting with ENC28J60 and PCA10056. Following are my connections:
================= =================================== NRF52840 PCA10056 ENC28J60 (pin...
Hi
I tried to implement Eddystone example in nRF52810. it worked successfully. Then i tried to implement same in nRF52832 using pca10040. But it not working. I only changed...
Hi, I'm running the saddc_pca10056 peripheral example given in SDK v15.2.0.
The analogue pin A0 is connected to the signal line of an LM35 temperature sensor. When I measure...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I am porting RTC example code as is into ble_app_blinky...
hi...
i want to advertise the multi link central example , i have added the advertising in code , now my central is advertising but when i tried to connect , i am getting...
I programmed a NRF52840 Dongle with the example light switch code having changed the channel to 14 which is what my coordinator is on.
I then programmed a NRF52840DK with...
Good day,
I program my nRF52-DK with BLE Eddystone example's pre-compiled hex:
\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_eddystone\hex\ble_app_eddystone_pca10040_s132...
