The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello everyone,
I am using nrf24l01p. It works fine but some times gets hang, doesn't receive data at all. I am sure that this is not the problem of micro controller because...
I am using the original board. Crystal of 32kHz has not been mounted on this. So, I want to use the internal RC Oscillator. In addition, I use a hrs example of nRF5_SDK_11...
From the product spec, I can operate in either low power mode or constant latency mode. It is not clear how much (or what mechanism) compromises the latency when low power...
Hello,
I'm developing an application that is sending data every certain seconds in a mesh network and, in order to reduce the power consumption, I wish the node enter...
i am using latest version mesh sdk 3.1 .. i want to interface two boards and want to check the bidirectional using text message, example if client sending the hello message...
Hi,
How can I Understand why the nRF9160 is disconnecting from the network?
How can I read the modem trace bin file to understand whats going on with the modem ?
Hello,
Do you have a soft device that integrates both Bluetooth and USB on the nRF52840 ?
I want to program a firmware that uses both and I'm wondering if you have ready...
What changes are needed in SDK V15 sdk_config.h so nRF52832 can run on internal RC oscillator?
I am using the BLE UART example, nRF52832 with Soft device s132_nrf52_6.0...
I want to extend the list of known UUIDs with some custom definitions but I am unable to open the Open UUID definitions file.
I tried following the Adding UUID definitions...
When connected with RTT viewer, a pin reset with nrfjprog shows a J-Link Error popup saying:
J-Link currently uses target interface SWD while current debugger tries to select...
Hi!
I want to send heartbeat messages from 30 servers to 1 client/provisioner.
I can send _HEARTBEAT_PUBLICATION_SET to every server like OpCode = _HEARTBEAT_PUBLICATION_SET...
Hi，
I have searched the posts about how to send/receive more than 255 bytes ,SPI master EasyDMA mode , but still can not find the solution.
I want to know if a ArrayList...
Hi,
i am facing two issue in nRF9160 cellular application.
1.Asset tracker Application:
i loaded Asset tracker example firmware in nRF9160 eval. board. when i run this...
Hello,
I'm porting a project from SDK14.2.0 to SDK15.3.0. Now, all is compiling, i need to figure out why my project is triggering some exception. To help me, i would like...
I am a newbie with nRF Sniffer, which I have installed on one PCA10040 board. I am sniffing communications between a Samsung phone running nRF Connect and a second PCA10040...
