The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello All,
Greetings!!!
I am working on nRF51822. I am used custom board. For reference i used nRF52 SDk 8.1.0 in IAR.
Right now i am use gpio pin as an interrupt pin...
I send 25 byte long messages to unicast addresses in a Mesh network. Because of their size messages become segmented. access_model_reliable_publish() is used for sending....
Hello,
I am using a combination of several Nordic devices and hardware. The nRF52832 is used in a sensor to collect light level information. That data is transported over...
Hello,
I wrote a simple program to turn on externally connected LED at Port 1 and Pin 10. But it is not working. See the code -
#include <stdbool.h> #include <stdint...
Is there any documentation about how to configure the SoftDevice clock configuration using the RC as SoftDevice clock source?
My target is the nRF52832 with the S132 Softdevice...
Folks,
We're wondering how the soft device can work with it being provided as a hex file? Usually with things like this you'd get object code to link to, but that doesn...
Hi,
I am currently working on a project for which I use the Secure Serial UART Bootloader from SDK 15.3 (nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart...
this device has 2 batteries. so I am adding 2 of battery service UUID(0x2A19). but I cannot access the other of UUID via windows API. but nRF connect for mobile can access...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Currently, only one ble_peripheral(based on nrf52840) can connect to the gateway (based on nrf52840) .
The other ble_peripheral( based on nrf52832), will bond to the gateway...
Hello,
As our product (nRF52832, SDK14.2) is heading to radio certification, I was playing around with the DTM example but have some open questions.
I've flashed the...
Hello,
ich have a custom board (with nRF52840 chip) which is programmed over SWD. So the Port ist easy accessable. As base software I am using example/radio_test.
I...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi I'm trying to get started with the the nrf52 Dev Kit and the Bluetooth Low Energy tutorial series, I've downloaded the first example "nrf52-ble-tutorial-advertising" from...
