Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
I'm currently on a question for which the documentation here can't help me.
If I'm correct, the Dual-Bank Update allows to retain a safe copy of the old firmware image...
Hi,
I am using esb project of SDK15.3 to test esb PTX and PRX function.
The default setting of address-0 and address-1 is 0xE7E7E7E7 and 0xC2C2C2C2, and PTX and PRX can...
Hi,
1.I want to develop the my product using nrf51822 with PCB antenna(as shape given in sdk hardware) with following board stackup-
2. i am going to use cap-0603 in...
Hi,
I am using nrf52840 S140 PCA10056 SDK 15.2.0 version with example ble_app_multirole_lesc_S140_PCA10056 . i am using Segger Embedded studio IDE. So now problemis i am...
Hi,
I am trying to get my systemOFF current below 1uA, but Im struggeling.
normally I use MBED, but to eliminate that variable, I just did a test without MBED, I took...
Hello together, I am experiencing problems with the nrf52840. I got the BLE_APP_Blinky example to run. Now I am trying to get the BLE_THROUGHPUT example experiment to run...
Dear nordic,
I want to know something regarding your SDK. I have nrf52832 development board and i use sdk 15.2 .
1. if i want to use BLE 4.2 version what changes i want...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I added the UART example to...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I used the nRF UART and nRF...
Dear nordic,
I need more information regarding this?
1. I heard the BLE one packet has possible 20 bytes. but i tested this example and connect using nRF connect app...
