Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
When using the script interactive_pyaci.py together with ipython and the serial example, I observe a strange formatting in the command window, because the "In [..]" is often...
SDK is nRF5_SDK_13.1.0_7ca7556.
Example is ble_ant_app_hrm.
Softdevice is S332.
The example can connect android but can not connect iphone.
Iphone 7 and ios is 10...
Disconnection of the peripheral is done without enabling another connection, the only way is to reset the module.
It happens sometimes after 5 min up to 1-2 hours.
If...
Hi all,
I'm working on an application that requires BLE. I've recently upgraded my project from sdk 14.0 to 15.2 in order to deal with some problems that I ran into with...
Hi,
I am trying to configure the nRF52810 clock setup to accept the LF CLK source from a pin on stm32l4xx on a custom board without much luck. My setup works correctly if...
Hello. I move ble_app_uart with a combination of nRF 52840-DK and SDK v 15.2.0. Using UART 0 or UARTE 0 confirms that it can communicate with nRF 52832 on the Central side...
Hi,
I am trying to understand the current consumption of a very simple BLE application running on the nRF52832 DK. For my final use case, I'd like to reduce the peak current...
Our project uses a Raspberry Pi compute module 3 connected via UART to 2 nRF51822. I'll go through what is working and than describe the issues I'm having
What's going...
Hi, I'm using ble_app_hrs_freertos from SDK 15.2 on PCA10056. I noticed that logs stop working (RTT) when I increase configTOTAL_HEAP_SIZE to 64k. I tried play with various...
I've got myself one an E73-2G4M04S1A board containing an nRF52810 chip for evaluation. I've setup an Raspberry Pi 1 rev2.0 with OpenOCD using this guide and wired it up according...
Hello,
i have bought 3 modules from Rigado (BMD-330-A-R) with a nRF52810 SoC, is it possible to flash it with an Raspberry Pi? I read that SWD is possible by its SPI-Interface...
We are in progrees of developing a wearable device using NRF52832 with BLE. The problem is, we have quite a few chips dead after several times of rewriting. The dead chips...
Hi,
I tried adding PWM for turning on/off the LED's on the DK for the Enocean switch example. It worked well.
I tried to perform dimming on the switch example by restricting...
Hello All,
This is a trivial question I guess but I am not able to figure out
Working on : nRF5 SDK for Mesh v2.2.0
SDK version : nRF5_SDK_15.0.0_a53641a
I have...
