The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello,everyone,
I have successfully installed nrfutil using pip install nrfutil, but when I type nrfutil in the terminal, it shows -bash: nrfutil: command not found, how...
Hi,
We were trying out the long range central and peripheral examples found in github with the nRF52840 DK boards but we are not getting the specified range(We did switch...
Hi everyone, I have nRF52840 DK and I want to write an application program that uses multiple wireless communication protocols (e.g BLE , Zigbee , Thread) and can communicate...
Hi,
I am trying to add Nordic UART service(NUS) in ble_app_relay_rscs, but after adding nus service in application device is not advertising and there is no print in serial...
Hi! I am trying to read the voltage of a LiPo battery as explained in this blog post. The code on github however, is not compatible with the latest SDK for the SOC (12.3)...
Hey guys,
we are currently evaluating the pc-ble-driver-js. We want to get it running on a Raspberry Pi 3.
The Nordic nRF52840 module was flashed with SD Version 6.1.0...
Hi,
i am using nrf51822 interface with mpu9250 and i want to detect a tap without using of DMP feature of mpu motion sensor. my application requirement is low current consumption...
Hi,
sending some data from nRF52840 (DK or dongle) to a host computer via USB. When nRF52840 is connected to a "powerfull" host, all goes ok; when connecting to a "less...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
hello,
Now i transplant pwm_library programming to ble_app_uart_c(central) in SDK15.0.
But i found the program cann't run in NRF52 DK.
I found it build no errors but...
Hello,
We are evaluating now a new project and I am struggling to get a feeling about one moment of Thread network and its particular implementation with nRF52840.
In...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
