Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi, I made a simple diagram of what my device should do:
The nRF52840 should receive data via SPI from another controller, mathematically process this data, and output...
Hi,
I just pulled the source code of 'nrf' from the git server (SHA1 ID: 383da27cc232bd7baa353e965b7fe8fa08b56d77).
After performed 'west update' to sync other repos,...
Hello!
I want merge and write via SWD full firmware, including: main firmware, bootloader, settings page.
When I start debug, all data correctly writed, but main firmware...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello,
My device has GATT data attributes configured to have BLE_GATTS_VLOC_USER so the data are in application stack. In this way, the softdevice has direct access to the...
I've been trying to use the Adafruit nRF52 library ( github.com/.../Adafruit_nRF52_Arduino) and the Arduino IDE to program a nrf52832 using my nrf52840 DK. However, I keep...
Dear Sir,
I wanted to make the peripheral connect to a predefined central device. Here I am using an android phone ( with nRFConnect installed in it) as the central device...
Hi,
I Used nRF52832-CIAA-R in my ongoing product development.
I need two UART and one I configured PIN(P0.6 and P0.8) for GSM.
Can I use any GPIO pin as a UART for GPS...
Hi,
when debugging nRF52 chips, currently using nRF52840-DK with arm-none-eabi-gdb (version 8.2.50.20181213-git), is the use of 'commands' supported?
Trying to see some...
I am using nRF51422 with the SDK 11. I am using the proximity application to measure the battery service. By default, the device uses VDD as its ADC input. I would like to...
Hi
We are using the version 2.0.1 soft device and it consumes 8kb RAM. We have a challenge with RAM on our device so we're looking for ways to make more RAM available for...
Using https://github.com/NordicSemiconductor/pc-ble-driver ( abce7974fe983c23930d362b1769e51c8fa13cbf) .
Just followed the instruction and compiled hex/sd_api_v6/connectivity_...
Hello,
I have a basic queries on BLE.
"Characteristic Properties" of "Characteristic Declaration" with UUID 0x2803 has Read, Write, Notify and Indicate. At the same...
Hi
Can I think so,if subscription address is identical in multiple nodes,then they are a group?
If so:
the light_1&light_2 OnOff Server Model subscription address is...
