Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
A general question about the radio CRC registers: The CRCPOLY register is 24 bits wide, which can be used to specify a 24-bit polynomial, suitable for calculation a 23 bit...
Hello Everyone,
I need to turn off the bluetooth advertising on certain event/interrupt and start advertising again on another event/interrupt.
I have gone through the...
Have a nice day! We are working on a project where goal is to build up mesh-network up to 50 nodes with high sum data rate to up 100kbps through the node. For this purposes...
Is there any release timeline for a Nordic Thingy based on the nRF52840? Does anybody know of an open-access beacon that incorporates the nRF52840? Thank you.
I'm trying to communicate with a single NeoPixel ( WS2812B) using the PWM module.
I've configured a sequence array with the compare values necessary to turn on the red and...
Hi everyone
I'm trying to get the status of button by using the bsp_event_callback_t, but my application crashes when I push on any button.
Test environment: Freertos...
Hi Team,
For the board having Linux Host having nRF52832 interfaced over UART, what are the maximum number of BLE devices can be connected?
As per my understanding it...
Hello, this is Kwonjoon Lee, beginner of BLE development.
I successfully installed pc-ble-driver (c/c++) in accordance with Git-Hub guide ( https://github.com/NordicSemiconductor...
Hello,
This is Jahnavi. I am having nrf52 DK development kit and with that development kits I am using light switch example to connect the boards as mesh network. How...
Hallo everyone,
I'm using Eclipse IDE for C/C++ Version 2018-12 (4.10.0), my OS is Ubuntu 18.04.2 LTS and my hardware is the NRF52840 DK. I'm using the GCC C and C++ Compiler...
Hello:
I have nRF9160 SIP custom board. The pins on custom board almost the same as nRF9160DK.
I can run lte_ble_gateway sample on nRF9160DK without problem:
But...
I followed nRF Connect SDK 0.3.99 to test nRF9160 LTE Sensor Gateway.
I successfully completed steps 1 thru 10 in the Testing section
It was successfully connected...
Hi all,
I am communicating with a sensor through UART using APP_UART on a custom board (nrf52840) through the nrf52 DK. I can send and receive commands to and from the sensor...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
We are using nRF52840 with BLE and 802.15.4 concurrent with S140 SoftDevice. There are two functions to set the transmit power for each radio protocol:
sd_ble_gap_tx_power_set...
