Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi,
I think I already know the answer but just to be sure, there is no difference on using printf (with added retarget library) and the app_uart_put() since printf will...
Hi, This is what constant carrier looks like at 2450MHz on my custom board using DCDC disabled
This is with DCDC enabled:
It can also look much worse with no real...
Hi there,
I'm looking at porting (i.e. re-implementing) an Arduino project to the nRF52832 to take advantage of the s212 or S332 softdevices. This chip is a few orders of...
I want to created a connectable iBeacon with nRF52810. I would like to connect my beacon through an app like nRF Beacon app and would like to configure....
* UUID
* Major...
Trying to run the SPI Master application on a custom nrf52382 based device (custom PCB) to communicate with an ADC chip that is taking analog values from a Multiplexer. Not...
I've designed a custom board for the NRF52832. Current consumption is not a major concern, and the pin location was convenient, so I wanted to use P0.00 and P0.01 for I2C...
Hi,
This is a problem report for the Programmer App v1.0.1 on nRF Connect v2.6.1 on MacOS 10.14.2. I have been attempting to use the programmer app with the nRF52 Dongle...
Hi all,
I have a trouble. I use 2 Dev Kit NRF52832. Flash light switch server proxy and light switch client proxy. Issue is when I erase and flash the first time, Client...
I'm developing an application for the nRF52832 using the nRF5 SDK version 15.0.0. We're using the s132 softdevice, the sample secure bootloader (modified to use our company...
Hi, I have been running into a problem where I am getting inconsistently failure to start advertising.
Calling:
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hello, I'm trying to write code to a custom PCB with a nRF52832 using the nRF52 DK and the following wiring:
However, everytime I try to connect the JLink is says...
I'm fairly new to working this close to hardware and am playing around with a few things. I'm trying to bit bang i2c over a couple of gpio lines and everything seems to be...
1.Does nRF52840 and nRF9160 have conformal shielding in manufacture procedure？
2.Do i need reserve shield cover for these two module when I develop product？
Hello,
I'm having trouble adapting my code which works for reading the MAX30100 sensor using TWI input with the NRF51 DK kit.
I would like to adapt this code to be used...
